Advanced Features - Blackstar Amplification ID:CORE STEREO 10 V3 Manual Del Usuario

Channel 3: Preamp output – The preamp sound of the Voice and EQ stage, taken
before the effects, and without any speaker cabinet emulation. Ideal for use with
your own effects and cabinet emulation plugins from your recording software/DAW.
Channel 4: Unprocessed guitar signal – The signal as it comes out of your guitar.
Record this signal for later use during Reamping (see 'Reamping' section below).
These audio streams can be recorded simultaneously within your chosen recording
software/DAW.
TIP: To record a truly Super Wide Stereo-effected sound – which is faithfully
recreated when playing back your recorded tracks on any stereo speakers – pan
the stereo emulated left channel 100% left in the mix, and pan the right channel
100% right.
Your ID:CORE amplifier can also receive audio input from your computer:
Channel 1: Line input, left channel – Used for audio monitoring or MP3/backing
track playback. Playback through the left internal speaker.
Channel 2: Line input, right channel – Used for audio monitoring or MP3/backing
track playback. Playback through the right internal speaker.
Channel 3: Reamping input – Send a pre-recorded unprocessed guitar signal to
your amplifier for Reamping, when in Reamping mode.
Channel 4: Unused
Reamping
The amplifier can be switched into Reamping Mode via the Blackstar ARCHITECT
software. This is a non-storable setting and will be switched off either when the USB
cable is removed, or when the amplifier power is switched off.
When activated, Reamping Mode allows the amplifier to accept a pre-recorded, dry
guitar signal via USB and return a fully processed audio signal. This return signal can
then be captured using recording software on the connected PC or Mac.

Advanced Features

Your ID:CORE amplifier has further advanced features which are aimed at more
in-depth users who enjoy getting the most from their amplifier. These features do
not have independent controls on the front panel of the amplifier, but instead are
accessed by using the Tap switch (11) as a 'shift key' and using other controls to
access these features.
Independent Music Playback Volume – Tap + Volume
Under most circumstances, the volume of your music playback via the MP3/
Line Input is effectively controlled directly from your playback device. For quieter
environments and general convenience you can also further reduce the music
playback volume of your ID:CORE amplifier by simply holding down the Tap switch
(11) whilst turning the Volume control (4) on the front panel.
16
USB Recording Level – Tap + Gain
As stated in the USB Audio section (see page 15), the output level of the USB
audio signal from your ID:CORE amplifier can be controlled independently of your
amplifier's speaker volume by holding down the Tap switch (11) whilst turning the
Gain control (3) on the front panel.
Effect Speed/Time – Tap + Effects Level
As stated in the Effect Level section (see page 10), the speed/time of the modulation
and delay effects can be controlled by holding down the Tap switch (11) whilst
turning the Effect Level control (10) on the front panel. This can be very useful for
setting a specific accurate effect tempo instead of using the Tap switch.
Firmware Update
Firmware updates are initiated via the Blackstar ARCHITECT software. A new
version of the Blackstar ARCHITECT software will be released whenever an update
is available.
Important note: Always connect the amplifier to a main USB port (usually found on
the on the rear of your PC or Mac) when updating the firmware. Never use a front
mounted USB port, USB hub or a USB extension cable. Doing so may result in a
failed update, which could cause your amplifier to become unresponsive.
When the amplifier is connected (via USB) to a version of the Blackstar ARCHITECT
software containing newer firmware, a message will be displayed prompting you to
install the latest files. Whilst updating, the amplifier controls will be unresponsive.
Front panel voice LEDs will cycle to indicate data activity during the update process.
The amplifier power should not be switched off during a firmware update. If the
amplifier is switched off during an update, the controls may be unresponsive after
the power is reapplied and the amplifier will produce no sound. The voice LEDs will
cycle to indicate that the amplifier contains no valid firmware.
If you are experiencing problems with the firmware update process the amplifier
can be forced to power up in Update Mode. Hold down the Manual (14) & MOD (6)
switches simultaneously, whilst switching on the amplifer to enter this mode with the
voice LEDs cycling to indicate Update Mode. Connect the amplifier to the Blackstar
ARCHITECT software to begin a firmware updae.
The amplifier must be connected to the Blackstar ARCHITECT software to
reinstall valid firmware. The update process will start automatically if the Blackstar
ARCHITECT software detects that the amplifier is in this state.
17