Technical Data - Seav RXB 2224 Guia De Inicio Rapido

RXX 2224 Dual channel receiver
The RxB 2224 Plus dual channel radio receiver allows the re-
mote control of electric and electronic devices via Smartphone
and/or one or more Seav Radio controls.
- Mod. RSB 2224 Narrow band :
- Mod. RHB 2224 Narrow band :

Technical Data:

- Work frequency:
- Power supply:
- Max. consumption:
- Op. radio control: 12-18-32 Fixed Bits, 66-80 bit Rolling Code
- Bluetooth Commands from Smartphone :
- Total Radio controls/Smartphone (CH1 + CH2) :
- no. 2 x Control relays:
- Working temperature:
- Dimensions:
- Radio control range in open space:
- Protection rating:
CN1 Terminal Board Connections:
1: Power supply 12-24 VAC-DC
2: Power supply 0V
3: "Normally open" contact output CH1
4: "Normally open" contact output CH1
5: "Normally open" contact output CH2
6: "Normally open" contact output CH2
Installation of the Receiver:
It is very important to choose the place of installation carefully in
order for the transmitter and the receiver to function well. The
range is not only affected by the technical features of the de-
vice, but also varies depending on the radio-electric conditions
of the site. The receiver has a tuned antenna.
The antenna must be positioned where it can be seen well
away from metal structures.
There must be a distance of at least 5 metres between the two
receivers if installation is to be successful.
GB
BlueTooth + 433,92 MHz
BlueTooth + 868,3 MHz
see model
12-24VAC-DC
5W
IOS/Android
330 Max
30VDC 1A
-10-55°C
53x82x40mm
50-100m
IP54
Power Supply Selection:
The power supply voltage can be selected by selection of the
Jumper J1:
Jumper J1: 12/24 VAC-DC power supply selection.
Pos. 1-2 = 12VAC-DC.
Pos. 2-3 = 24VAC-DC (default).
CH1 and CH2 Operating Mode:
The receiver is capable of separately managing two channels
and Monostable operating mode.
Sound Alerts:
1 SHORT BEEP = Confirms Storage/Connection.
2 SHORT BEEPS = Receiver ready to operate.
3 SHORT BEEPS= Storage/Programming Failed.
1 LONG BEEP = Bluetooth Disconnection.
2 LONG BEEPS = Radio controls/Smartphone Cancellation.
3 LONG BEEPS = Reset.
Rule for the 1st Radio Control Stored:
The following rule applies when programming the radio controls:
if the first radio control to be stored is the Rolling Code Plus
type, the control unit will only accept Rolling Code Plus radio
controls, thus guaranteeing a high degree of anti-cloning safety.
If the first radio control to be stored is the Rolling Code type, the
control unit will accept only Rolling Code and Rolling Code Plus
radio controls, thus guaranteeing a good level of anti-cloning
safety. Whereas if the first radio control to be stored is the fixed
code type, the receiver will accept fixed code radio controls and
Rolling Code and Rolling Code Plus radio controls without
managing the anti-cloning algorithm.
RCD Stand Alone programming:
The programming of the Radio controls to be associated is the
Self-learning type and is performed with the antenna not con-
nected in the following way:
press SEL once; the CH1 LED will start to flash; then send the
chosen code with the radio control, at a distance of a few me-
ters, when the CH1 LED remains on steady
emit a short Beep for confirmation, signalling that the radio con-
trol has been programmed on channel CH1.
To store a new radio control code in channel CH2, perform the
same procedure described above and pressing the SEL key
twice.
The memorisation procedure can be repeated up to a max. of
330 codes. When the memory is full by repeating the program-
ming operation, the CODE CH1 and CODE CH2 LEDs will start
to flash very quickly, the receiver will emit three short Beeps for
confirmation, indicating that it is not possible to store any more
codes.
Smartphone Stand Alone programming:
The programming of the Smartphine to be associated is the
Self-learning type and is performed in the following way:
press the SEL key three times, the Leds CH1 and CH2 will start
flashing, then open the " BeLite " application
and connect to the detected receiver, when
the Leds CH1 and CH2 remain on steady, the
receiver will emit a short beep confirms, indi-
cating that the programming
Smartphone in the receiver has been com-
pleted.
the receiver will
,
of the
Rev. 1.1 26/03/2021