Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
v ) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
w ) Use the power tool, accessories and tool bits, etc.
in accordance with these instructions, taking
into account the working conditions and the
work to be performed. Use of the power tool for
operations different from those intended could result
in a hazardous situation.
Service
x ) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
Electrical Safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
WARNING! If the power cord is damaged,
it must be replaced by the manufacturer,
authorized BLACK+DECKER Service Center or
an equally qualified person in order to avoid
damage or injury. If the power cord is replaced by
an equally qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
Labels on Tool
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V ......................... volts
Hz ....................... hertz
min ..................... minutes
or DC ...... direct current
...................... Class I Construction
(grounded)
.../min .............. per minute
BPM .................... beats per minute
IPM ..................... impacts per
minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM .................... strokes per minute
A ......................... amperes
W ........................ watts
or AC ........... alternating current
ADDITIONAL SPECIFIC SAFETY RULES
Safety Warnings Common for Sanding
Operations
•
Hold the power tool by insulated gripping surfaces,
because the sanding surface may contact its own
cord. Cutting a "live" wire may make exposed metal parts
or AC/DC .... alternating or
direct current
...................... Class II
Construction
(double insulated)
n o ....................... no load speed
n ......................... rated speed
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation
..................... wear respiratory
protection
..................... wear eye
protection
..................... wear hearing
protection
..................... read all
documentation
of the power tool "live" and could give the operator an
electric shock.
•
Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body leaves it unstable
and may lead to loss of control.
WARNING! Contact with or inhalation of dusts
arising from sanding applications may endanger
the health of the operator and possible bystanders.
Wear a dust mask specifically designed for protection
against dust and fumes and ensure that persons
within or entering the work area are also protected.
•
Thoroughly remove all dust after sanding.
•
Take special care when sanding paint which is possibly
lead based or when sanding some woods and metal
which may produce toxic dust:
•
Do not let children or pregnant women enter the work area.
•
Do not eat, drink or smoke in the work area.
•
Dispose of dust particles and any other debris safely.
•
The intended use is described in this instruction manual.
•
The use of any accessory or attachment or performance of
any operation with this tool other than those recommended
in this instruction manual may present a risk of personal
injury and/or damage to property.
•
An extension cord must have adequate wire size
for safety. The smaller the gauge number of the wire,
the greater the capacity of the cable, that is, 16 gauge
has more capacity than 18 gauge. An undersized cord
will cause a drop in line voltage resulting in loss of power
and overheating. When using more than one extension
to make up the total length, be sure each individual
extension contains at least the minimum wire size. The
following table shows the correct size to use depending on
cord length and nameplate ampere rating. If in doubt, use
the next heavier gauge. The lower the gauge number, the
heavier the cord.
Minimum gage for cord sets
Volts
Total length of cord in feet (ft)
120 V - 127V
0 - 25
220 V
0 - 50
Ampers
Wire gauge in square millimeters
More
No more
than
than
0
6
1,0
6
10
1,0
10
12
1,5
12
16
2,5
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
Safety of Others
•
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
hey have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
ENGLISH
26 - 50
51 - 100
101 - 150
51 - 100
101 - 200 201 - 300
(mm
)
2
1,5
1,5
2,5
1,5
2,5
4,0
1,5
2,5
4,0
4,0
Not recommended
19
Publicidad
Tabla de contenido
