Headlamp Kawe Hilight Led H-800; Technical Data - KaWe HiLight LED H-800 Instrucciones De Empleo

User's Manual

Headlamp KaWe HiLight LED H-800

Dear buyer, we are grateful to you for choosing KaWe products Our pro-
ducts are of high quality and long-lasting. This KaWe device complies
with the provisions of Directive EU 2017/745 (European Directive on
Medical Devices), whereby it is classified as a medical device of class 1.
Please, read this user' s manual attentively and carefully and
pay attention to the maintenance recommendations prior to
use.
Please, carefully read the operating instructions prior to use.
Application: Headlamp KaWe HiLight LED H-800 shall be operated
only by the authorized qualified personnel.
Intended use: Headlamp KaWe HiLight LED H-800 is used as an illu-
minating device for medical examinations. The headlamp is put on the
head during operation in order to provide for optimal illumination of the
area under examination. Additionally, the headlamp may be equipped
with a binocular loupe to examine the region under magnification. The
following parameters can be selected (magnification x operating di-
stance): 2.5 x 340 mm, 2.5 x 420 мм, 3.5 x 340 mm, 3.5 x 420 mm.
Assembly/Disassembly: Headlamp KaWe HiLight LED H-800 shall be
connected to KaWe lithium ion battery. There is a cable for this on the
right, which is directly connected to the battery for the headrim or to the
battery cable for belt fastening. When the headlamp is used with the
battery for the head rim, it shall be fastened of its back side. For this
purpose, insert the clamping elements of the battery body to the
grooves on the back side of the head rim and clamp it with a light move-
ment. In order to disconnect the clamping elements, move them toge-
ther again to the opposite direction.
The binocular loupe can be fastened on the back in a holder under the
lamp body. For this purpose, loosen the fastening screw on the joint of
the binocular loupe. After insertion into the holder, fix the fastening
screw in the threaded hole on the front side. To regulate the position of
binocular loupes, slightly loosen them. Then tighten the fastening screw
to reliably fix the binocular loupes in the required position.
Improper use of the device/contraindications for use: Any other
use of use outside the above indication shall be considered improper. The
manufacturer is not responsible for damage resulting from such use.
Only the use is responsible for the risk. For power supply, use only the
battery in the delivery package or the original battery by KaWe.
Commissioning/Handling:
1. Connect the headlamp to the battery for the head rim or belt faste-
ning.
2. To switch the headlamp on, press and hold the control button for
approximately on second. The current charge of the battery is displa-
yed by short flashing of LED indicators. If none of the LED indicators
flashes, the battery is completely discharged.
3. After switching on the brightness is at the minimum. To increase
the brightness, turn the control knob clockwise. To decrease the
brightness, turn the control knob counterclockwise. The brightness is
indicated by LED indicators.
4. To switch off, press and hold the control knob for approximately
one second.
5. When putting the headlamp on, make sure it fits tight.
Charging of batteries:
1. To charge the batteries of the headlamp, use only a special power
unit with an integrated plug included into the delivery package.
2. When the green LED is on at the power unit, the connected battery
is charging. During charging, LED indicators on the respective battery
remain dark.
3. The green LED at the network power unit goes off, when the batte-
ry is fully charged.
4. The headlamp shall not be operated during charging. In this condi-
tion, the battery shall not be switched on.

Technical data:

Permissible ambient temperature +10 °C to +40 °C
Relative humidity
Storage temperature
Atmospheric pressure
Protection rating
Input voltage
(network power supply unit)
Output voltage
(network power supply unit)
Capacity
Weight (without the battery)
Duration of the battery
operation (head rim)
Duration of the battery
operation (belt fastening)
Life span (battery)
Life span (LED indicators)
*: Duration of operation at the maximum brightness.
The less the brightness, the more the operating time.
6
10 % to 75 %
+5 °C to +60 °C
700 to 1060 hPa
IP X0
100-240 V alternating
current, 50/60 Hz
8.4 VDC
Belt battery: 3 000 mAh
Head rim battery: 1,500 mAh
about 260 g
about 4 hours*
about 8.5 hours*
at least 500 charging cycles
about 50.000 hours