Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
FRAME
Hitch Shown In Proper Position
Equipment Required: Bolt leader (Provided)
Fastener Kit: 65060F
Wrenches: 18MM DEEP WELL, 7/8"
Drill Bits: 1/2"
Other Tools: Tape, Cutting tool for hard
Plastic fascia. File for enlarging hole.
TRIM FASCIA AS SHOWN
This is a magnified
5
view of a Bolt Leader
j
Qty. (4)
Carriage Bolt, 1/2" -13 x 2" Gr5
l
Qty. (4)
1/2" Helical lock washers
1.
It is necessary to trim a section out of the plastic fascia attached to bottom of bumper. See Picture
above.
CONSULT VEHICLE OWNER BEFORE TRIMMING OR CUTTING PLASTIC AIR DAM.
2.
Locate and remove the18mm flange nuts on outside of truck frame rails, slide the bolt plate back into
frame but do not remove.
CAUTION: DO NOT completely remove bolt plate, if removed bumper will drop and may result in injury.
3.
Raise hitch into position, slide bolts plates back thru frame and into hitch side brackets. Loosely install
nuts removed in Step 2.
4.
With front Bolts installed use rear holes as a guide to drill (4) 1/2" holes into frame.
5.
Use 1/2" bolt leaders to pull 1/2" carriage bolts and spacer blocks thru hole (if hole is not available you
must enlarge existing hole or drill one for the hardware) in the frame and through the hitch as shown
(FIG.2). Square shoulders of bolts must be pulled into blocks to engage with the sides of frame. Check
to see that carriage bolt is engaged in block holes. Install helical lock washers and hex nuts as shown.
6.
Tighten flange nuts and torque all hardware to the specs specified below.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2012 Cequent Performance Products
Front Mounted Receiver
FASCIA
Installation Instructions
1"
3 ½"
FIG.2
Frame rail
Tighten all 1/2" fasteners with torque wrench to 75 Lb.-Ft. (101.7 N.M.)
Tighten all M12 fasteners with torque wrench to 92 Lb.-Ft. (124.7 N.M.)
Dodge 3500
9,000lb.
k
Qty. (4)
Block 1/4" x 1-1/2" x 2
m
Qty. (4)
Hex Nut, 1/2"
Sheet 1 of
65060N
Part Numbers:
CARGO CAPACITY – Do not exceed
500 LB (227 Kg.) or Truck Front
Gross Axle Weight Rating, (GAWR).
MAXIMUM WINCH LINE PULL
Bolt
Plate
FIG.1
3
4
Bolt
leader
8-20-12
Form: F205 Rev A 5-6-05
65060
1
2
Rev. A
Publicidad
Manuales relacionados para Cequent Performance Products 65060
Resumen de contenidos para Cequent Performance Products 65060
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 65060N 8-20-12 Rev. A 2012 Cequent Performance Products Form: F205 Rev A 5-6-05...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 1 de 65060N 8-20-12 Rev. A 2012 Cequent Performance Products Form: F205 Rev A 5-6-05...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Hoja 1 de 65060N 8-20-12 Rev. A 2012 Cequent Performance Products Form: F205 Rev A 5-6-05...