Cequent Performance Products 65078 Manual De Instrucciones

Hitch Shown In Proper Position
Equipment Required: Utility Knife,
Tape Measure & Marking Pencil. (Die
grinder required for GMC)
Fastener Kit: 65078F
Wrenches: 3/4" & (2) 18mm
Drill Bits: None
Reverse pullwire technique
Example of
pullwire procedure
Fascia not shown.
Fascia trim required. Obtain vehicle owners approval before cutting
1 1 1 1 Qty. (2) Carriage bolt 1/2-13 X 1.750 GR5
2 2 2 2 Qty. (2) ¼" x 1 x 2 Block
Trim fascia for receiver tube.
1. Trim fascia. See fascia trimming information (page 2) for proper vehicle model:
Note: CONSULT VEHICLE OWNER BEFORE TRIMMING.
2. Remove the flange nuts and the 2 long bolts (1 each side) and 2 flange bolts (1 each side) from bottom of frame to rail existing
tow hooks. Keep for re-installation.
3. Using the reverse fishwire technique (example above), install the included carriage bolts and blocks through the 1" diameter
hole on the bottom of the frame rail, leave bolt leaders attached.
4. Raise hitch into position as shown.
5. During this process, feed the pullwires through the rearward slots in the hitch, once into position remove pullwires and attach
conical washers and hex nuts to hold hitch in place.
6. Re-install the long M12 bolts removed earlier through the upper holes in the hitch and through the tow hook (while holding it in
proper position and attach the flange nuts removed earlier.
7. Re-install the shorter M12 flange bolts through the hitch and frame rail into the threaded hole in the bottom of the tow hook.
8. Tighten all fasteners to the required torque specification.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
© 2014, 2017 Cequent Performance Products – Printed in Mexico
Installation Instructions
Chevrolet Silverado 2500 HD, 3500 HD
GMC Sierra 2500 HD, 3500 HD
Does not fit Denali HD due to extensive fascia cutting
Note: Fascia trim required. Obtain vehicle owners approval before cutting
Fascia
NOTE: If front mounted license
plate is present, repositioning
may be necessary.
1 1 1 1
2 2 2 2
Existing flange nut
for existing tow
hook
Existing tow hook
Existing M12 Flange Bolt
Tighten all 1/2 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Tighten all M12 CL10.9 fasteners with torque wrench to 92 Lb.-Ft. (125 N*M)
CARGO CAPACITY – Do not exceed
500 LB. (227 Kg) or Truck Front
Gross Axle Weight Rating, (GAWR).
9,000 lb.
(4086 Kg)
Crossmember shown
Cut off for clarity
Existing M12 Flange Bolt
3 3 3 3
4 4 4 4
3 3 3 3 Qty. (2) Conical Toothed Washer
4 4 4 4 Qty. (2) Hex Nut ½-13
Sheet 1 of 6 65078N
Part Numbers:
65078
MAXIMUM WINCH LINE PULL
MAXIMUM WINCH LINE PULL
Note: Fasteners typical
both sides
1 1 1 1
2 2 2 2
Existing flange nut
for existing tow
hook
3 3 3 3
4 4 4 4
6-27-17 Rev. A
Form: F205 Rev A 5-6-05