Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Fascia
Receiver Shown In Proper Position
Hitch Requires 5/8" Pin and Clip
Equipment Required:
Fastener Kit: F65043
Wrenches: 7/8"
Drill Bits: None
1
Qty. (4)
Hex Bolt, 1/2"-13 x 6"
2
Qty. (2)
Conical Washer, 1/2"
3
Qty. (2)
Tubular, Spacer
4
Qty. (4)
Flat Washer, 1/2"
1.
Raise receiver into position and select attaching holes in side brackets to allow for fascia clearance.
2.
Place conical toothed washers and tubular spacers onto hex bolts and position into round holes in vehicle frame rails as shown in Figure 1.
3.
Tubular spacers must be positioned to rest on the edges of the holes in the vehicle frame rails. See Figure 2.
4.
Insert hex bolts through flat washers and the square holes in vehicle frame rails. Place 1-1/2" x 2" x 1/4" blocks between the inside surface
of the frame rails and the receiver side brackets.
5.
Install flat washers, lock washers and hex nuts on the forward attachments and 1-1/2" x 2" x 1/4" blocks and hex nuts on the rearward
attachments.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. A hitch or ball which has been damaged should be removed and replaced.
Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch. Do not cut, weld, or
modify hitch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2005 Cequent Towing Products
Front Mounted Receiver
Installation Instructions
Ford F-150
Lincoln Mark LT
Fascia
Additional Hole Pattern
For Ground Clearance
FASTENERS TYPICAL
BOTH SIDES
Frame Rail
Optional Hole Pattern
For Ground Clearance
FIGURE 1
Tighten all 1/2" GR5 fasteners with torque wrench to 75 Lb.-Ft (102 N-m).
CARGO CAPACITY – DO NOT EXCEED
500 LB. OR VEHICLE FRONT GROSS
AXLE WEIGHT RATING. (GAWR)
9000
5
Qty. (4)
Spacer, 1-1/2" x 2" x 1/4"
6
Qty. (2)
Lock Washer, 1/2"
7
Qty. (4)
Hex Nut, 1/2"
Sheet 1 of 3
N65043
Part Numbers:
65043
LB. MAX. WINCH LINE PULL
Frame Rail
Tubular
Spacer
FIGURE 2
11-07-05
Rev. B
Publicidad
Manuales relacionados para Cequent Towing Products 65043
Resumen de contenidos para Cequent Towing Products 65043
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 N65043 11-07-05 Rev. B 2005 Cequent Towing Products...
- Página 2 Ne pas découper, souder ni modifier l’attelage. Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage Feuille 2 de 3 N65043 11-07-05 Rev. B 2005 Cequent Towing Products...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684 Hoja 3 de 3 N65043 11-07-05 Rev. B 2005 Cequent Towing Products...