Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Truck cab mount
Bumper
Truck frame
Receiver Shown In Proper Position
Equipment Required:
Fastener Kit: 65049F
Wrenches: 13/16", 7/8", 15/16"
Drill Bits: None
4
3
2
1
Bolt Leader shown
7
6
This is a magnified view
of a Bolt Leader
Qty. (2)
Hex Bolt, 9/16"-12 x 2" Gr5
1
Qty. (2)
Flat Washer, 9/16"
2
Qty. (2)
Lock Washer, 9/16"
3
Qty. (2)
Hex Nut, 9/16"
4
1.
On newer model 4 wheel Drive trucks it is necessary to trim plastic air dam attached to bottom of bumper.
2.
Position hitch and install fasteners as shown above. Using 5/8" bolt leader to pull 5/8" carriage bolt into frame slot.
3.
Torque fasteners to specifications below.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body
panels to prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety
precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.
Regulation V-5 and SAE J684.
z
2007 Cequent Towing Products
Front Mounted Receiver
Installation Instructions
Ford SuperDuty 250/350/450
All including Cab-on-Chassis
Air dam
8
5
4
CONSULT VEHICLE OWNER BEFORE TRIMMING.
Tighten all 9/16" GR5 fasteners with torque wrench to 110 Lb.-Ft (149 N-M).
Tighten all 5/8" GR5 fasteners with torque wrench to 150 Lb.-Ft (203 N-M).
CARGO CAPACITY – Do not exceed
Gross Axle Weight Rating, (GAWR).
Forward truck
9,000lb.
frame
Truck frame cut-away to
show Bolt Leader through
slot in truck frame
Rear tab of hitch aligns with slot
in frame between mount bracket
3
2
1
7
6
8
Qty. (2)
5
Qty. (2)
6
Qty. (2)
7
Qty. (1)
8
Sheet 1 of 3
Part Numbers:
500 LB.
or Truck Front
MAXIMUM WINCH LINE PULL
Mount bracket cut-away
to show detail
5
Carriage Bolt, 5/8"-11 X 1-1/2" Gr5
Lock Washer, 5/8"
Hex Nut, 5/8"
Bolt Leader, 5/8"
65049N
6-6-07
65049
Forward truck cab
mount bracket
End of Bolt Leader
Rev. A
Publicidad
Manuales relacionados para Cequent Towing Products 65049
Resumen de contenidos para Cequent Towing Products 65049
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2007 Cequent Towing Products Sheet 1 of 3 65049N 6-6-07 Rev.
- Página 2 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. 2007 Cequent Towing Products Hoja 2 de 3 65049N 6-6-07 Rev.
- Página 3 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 2007 Cequent Towing Products Feuille 3 de 3...