Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Rearward
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75792F
Wrenches: 7/8"
j
Carriage Bolt 1/2"-13 x 1-3/4" GR. 8
Qty. (4)
k
Block 1/4" x 1" x 3"
Qty. (4)
l
Hex Nut 1/2"-13 GR. 8
Qty. (4)
1.
Using the pull wire procedure shown above, install the carriage bolts and blocks into the frame rail. Leave the pull wires attached.
2.
Position the hitch beneath the frame rail as shown.
3.
Use the pull wires to insert the carriage bolts through the attachment holes of the hitch. Remove the pull wires.
4.
Install the flat washers, lock washers, and nuts as shown.
5.
Torque all fasteners to specification.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
© 2013 Cequent Performance Products, Inc.
Printed in Mexico
Frame rail
Installation Instructions
Fascia
Note: Fasteners typical both sides
Tighten all 1/2"-13 GR. 8 fasteners with torque wrench to 110 Lb.-Ft. (149 N*M)
Isuzu D-Max
Do Not Exceed Lower of Towing Vehicle
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: PU3
Existing hole
Example of Pull Wire Procedure
m
Lock Washer 1/2"
Qty. (4)
n
Flat Washer 1/2"
Qty. (4)
o
Pull Wire 1/2"-13
Qty. (4)
Sheet 1 of 3
Part Numbers:
Manufacturer's Rating or
Max Gross
Trailer WT (LB)
6,000 (2724 Kg)
4,000 (1816 Kg)
Accessory Rating
Kink pull wire to keep block
independent of bolt
o
75792N
10-16-13
Form: F205 Rev C 9-17-2012
75792
Max Tongue
WT (LB)
600 (272 Kg)
600 (272 Kg)
C
j k
l m
n
Rev. A
Publicidad
Manuales relacionados para Cequent Performance Products 75792
Resumen de contenidos para Cequent Performance Products 75792
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. © 2013 Cequent Performance Products, Inc. Sheet 1 of 3 75792N 10-16-13 Rev.
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. ©2013 Cequent Performance Products, Inc. Feuille 2 de 3...
- Página 3 Observe las precauciones de seguridad al trabajar por debajo del vehículo y use protección visual. No corte los orificios de acceso o accesorios con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. © 2013 Cequent Performance Products, Inc. Hoja 3 de 3 75792N 10-16-13 Rev.