Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Frame rail
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75688F
Wrenches: 5/8" 11/16", 22mm ,
6" Ratchet Extension, & Ratchet
swivel
65
43
Passenger's
bracket
1
Qty. (2)
Hex bolt M14 X 2.00 X 120mm CL8.8
2
Qty. (2)
Conical washer 5/8"
3
Qty. (3)
Hex bolt 7/16-14 X 1.50 GR5
Use caution when working near exhaust.
1. Prior to installation thread M14 bolts (Item 1) into both weldnut to clean out dirt & rust.
2. Raise hitch over tail pipe on the driver's side and start to install rearward bolt to support hitch.
3. Place passenger's bracket against existing tie down bracket on vehicle and install 7/16" hardware as shown.
4. Install forward M14 bolts (Item 1) into weldnut (push tail pipe forward and rotate bolt to get it into place).
5. Torque all fasteners to specifications.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2010 Cequent Performance Products
Installation Instructions
Fascia
Rearward
bolt
Tail pipe
Existing tie
down bracket
Tighten all M14 CL8.8 fasteners with torque wrench to 100 Lb.-Ft. (136 N*M)
Tighten all 7/16-14 GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Land Rover LR2
Do Not Exceed Lower of Towing Vehicle
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location:
Weld nuts
2
1
4
Qty. (3)
5
Qty. (3)
6
Qty. (3)
Sheet 1 of 3
Manufacturer's Rating or
Max Gross
Trailer WT (LB)
4000 (1816 Kg)
4000 (1816 Kg)
Existing tie
down bracket
65
Lock washer 7/16"
Flat washer 7/16"
Hex nut 7/16-14
75688N
2-22-10
Part Numbers:
75688
87575
44640
78180
U-Haul
Max Tongue
WT (LB)
400 (182 Kg)
400 (182 Kg)
43
Rev. A
Form: F205 Rev A 5-6-05
Publicidad
Manuales relacionados para Cequent Performance Products 75688
Resumen de contenidos para Cequent Performance Products 75688
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 75688N 2-22-10 Rev. A 2010 Cequent Performance Products Form: F205 Rev A 5-6-05...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 75688N 2-22-10 Rev. A 2010 Cequent Performance Products Form: F205 Rev A 5-6-05...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684 Hoja 3 de 3 75688N 2-22-10 Rev. A 2010 Cequent Performance Products Form: F205 Rev A 5-6-05...