Publicidad
2.4
CONNECTION AND PREPARATION OF EQUIPMENT
FOR GAS TUNGSTEN ARC WELDING (TIG) LIFT.
• TURN OFF WELDER BEFORE MAKING CONNECTIONS.
Connect all welding accessories securely to prevent power
loss. Carefully follow safety precautions described.
1.
On the unit preset Lift TIG welding (Rif.1 - Pic. 1 page 4.).
2.
Fit the required electrode and nozzle to the electrode holder
(Check the protrusion and state of the electrode tip).
3.
Connect the ground cable quick connection to the positive (+)
receptacle and the clamp near the welding zone.
4.
Connect the torch power cable connector to the negative re-
ceptacle. (-).
5.
Connect the gas hose to the regulator located on the gas cyl-
inder.
6.
Adjust welding current with ampere selector (Rif.3 - Pic. 1
page 4.).
7.
Open the gas valve on the torch.
8.
Turn ON the power source.
3.0
CONTROLS
3.1
FRONT PANEL - REAR PANEL
Picture 1.
5
2
Picture 2.
4
1 - PROCESS SELECTOR (Rif.1 - Pic. 1 page 4.) : In this position
welding can be used with rutile, basic electrodes, and specially
coated electrodes.
All manuals and user guides at all-guides.com
CONTROLS
welding process with lift mode
ignition can be selected, as de-
scribed previously.
TO IGNITE THE ARC, when
TIG welding,proceed as fo lows:
Touch the welding piece with the
electrode; this will cause a short-
circuit between the piece (2) and
the electrode (1). Lift off the
electrode; the arc will ignite. The
integrity of the electrode tip is
guaranteed by the low ignition
current during short-circuiting
between the welding piece and
the electrode ignition is guaran-
teed even at minimum welding
current settings; the operator
can therefore work without con-
taminating the ambient with
electromagnetic disturbance,
normally caused by high frequency discharges.
The advantages can be this summarised:
3
1
2 - FAULT LED (Yellow) (Rif.2 - Pic. 1 page 4. ) : When the fault
led lights on, the overheating occurs inside the unit due to the ex-
ceeding the rated duty cycle. Happening that the welding opera-
tions have to be stopped, the welding power source has to be kept
on until the led lights off so the unit is ready to weld again.
3 - CURRENT REGULATION (Rif.3 - Pic. 1 page 4.) : this poten-
tiometer adjust the welding current range.
5 - ARC LED ILLUMINATED (Green) (Rif.5 - Pic. 1 page 4.) : this
led lights when the machine is turn on.
N. B.: the power source is fitted with an anti-sticking device that
disables power if output short circuiting occurs or if the electrode
sticks, allowing it to be easily detached from the workpiece. This
device enters into operation when power is supplied to the gener-
ator, even during the initial checking period, therefore any load in-
put or short circuit that occurs during this phase is treated as a
fault and will cause the output power to be disabled.
4.0
IMPORTANT: DISCONNECT THE POWER PLUG AND WAIT
AT LEAST 5 MINUTES BEFORE CARRYING OUT ANY MAIN-
TENANCE. MAINTENANCE MUST BE CARRIED OUT MORE
FREQUENTLY IN HEAVY OPERATING CONDITIONS.
4 EN
LIFT TIG PROCEDURE
In this position the TIG
a. l no need for high-frequency startups;
b. l no damage to the electrode tip during start-ups, regard-
less of ampere setting, thereby avoiding the presence of
tungsten in the welding piece, common during scratch
starting.
SWITCH-OFF: To quit the welding phase the operator
can use the conventional pull method or alternatively a
newly introduced method that simulates the torch button.
This method enables a downslope to be had without torch
button. During the welding phase the operator only has to
move away from the piece in order to start a downslope,
whenever he wants to stop the slope (without waiting the
time necessary for its closing) the operator just has to pull
the arc like a normal TIG lift. The duration of the slope de-
pends on the current set and being able to guarantee op-
timal closing of the crater.
4 - ON - OFF SWITCH: This switch (Rif. 4 - Pic. 2 page
4.) has two positions: ON= I and OFF = O
MAINTENANCE
EN
Publicidad
Capítulos
