Introduction Thank you for purchasing the Ubiquiti Networks® EdgePower ™ This Quick Start Guide is designed to guide you through installation and also includes warranty terms. Package Contents EdgePower EP-24V-72W Mount Brackets Bracket Screws Wall Mount Wall Mount (Qty. 2) (Qty.
Hardware Overview Front Panel Ports DC Out Battery In Power RJ45 Ports 1-2 Interface Description RJ45 1-2 RJ45 switch ports support 10/100 Ethernet connections and 24V Passive Power over Ethernet (PoE) output. DC Out Connect the Power Cable with DC Jack to this terminal block for 24V, 3A output.
Front Panel Button Reset Button Description To reset to factory defaults: 1. Disconnect power from the device. 2. Reconnect power while holding the Reset button. The port LEDs will Reset repeatedly light up in sequential order (this takes approximately five seconds). 3.
Página 5
Front Panel LEDs System System LED State Status Flashing White Bootup in progress. Ready for use, not connected to Ubiquiti® White Network Management System (UNMS ™ Blue Ready for use, connected to UNMS. Steady Blue Ready for use, unable to connect to with Occasional UNMS, check connection to UNMS server.
Página 6
RJ45 LEDs Link/Act State Status No Power over Ethernet Green 24V Power over Ethernet No Link Link/ Amber Link Established at 10/100 Mbps Activity Amber Link Activity at 10/100 Mbps Flashing...
Hardware Installation The EdgePower can be mounted on a horizontal surface, mounted on a vertical surface, or mounted in a rack (rackmount accessory not included). WARNING: The EdgePower must not be stacked. Do not place it on top of another device. Do not place anything on top of the EdgePower.
Página 8
2. Connect the other end of the Power Cord to a power outlet. Using the Battery Input (Optional) For redundant power backup, connect an external battery (not included) to the EdgePower. Note: Only one power source can be used at any one time.
Página 9
Connecting Ethernet 1. Connect an Ethernet cable from your 24V PoE device(s) to ports 1-2 on the EdgePower. WARNING: Before enabling PoE passthrough in the EdgePower Configuration Interface, ensure that the connected PoE device supports 24V Passive PoE. Connecting DC Output 1.
Página 10
Accessing the Configuration Interface Access the EdgePower Configuration Interface to monitor status and power consumption, or to configure 24V Passive PoE and network settings. Note: The EdgePower is set to DHCP by default with a fallback IP address of 192.168.1.20. 1.
Página 11
Configuring PoE Settings The PoE setting for ports 1-2 is set to Off by default. WARNING: Before activating PoE, ensure that the connected device supports passive PoE and the supplied voltage. 1. In the EdgePower Configuration Interface, click the Power tab. 2.
Página 12
Specifications EP-24V-72W Dimensions 192 x 43.7 x 115 mm (7.559 x 1.72 x 4.528") Weight 650 g (1.43 lb) Interfaces Networking (2) 10/100 Mbps RJ45 Ports Management Ethernet In-Band PoE Output (2) 24VDC Passive PoE (Pins 4, 5+; 7, 8-) DC Output 24V, 3A Power Method...
Safety Notices Read, follow, and keep these instructions. Heed all warnings. Only use attachments/accessories specified by the manufacturer. WARNING: Failure to provide proper ventilation may cause fire hazard. Keep at least 20 mm of clearance next to the ventilation holes for adequate airflow. WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.
Página 14
Limited Warranty www.ubnt.com/support/warranty/ The limited warranty requires the use of arbitration to resolve disputes on an individual basis, and, where applicable, specify arbitration instead of jury trials or class actions. Compliance Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Página 15
CE Marking CE marking on this product represents the product is in compliance with all directives that are applicable to it. RoHS/WEEE Compliance Statement English European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste.
Página 16
Español La Directiva 2012/19/UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
Az EU-megfelelőségi nyilatkozat teljes szövege elérhető a következő internetes címen: www.ubnt.com/compliance Íslenska [Icelandic] Hér, UBIQUITI NETWORKS, því yfir að þetta EP-24V-72W tæki er í samræmi við grunnkröfur og önnur viðeigandi ákvæði tilskipana 2014/30/ESB, 2014/35/ESB. Fullur texti ESB samræmisyfirlýsing er að finna á eftirfarandi netfangi: www.ubnt.com/compliance...
2014/30/UE, 2014/35/UE. Il testo completo della dichiarazione di conformità UE è disponibile al seguente indirizzo Internet: www.ubnt.com/compliance Latviešu valoda [Latvian] Ar šo, UBIQUITI NETWORKS, deklarē, ka EP-24V-72W ierīce, ir saskaņā ar būtiskajām prasībām un citiem attiecīgiem noteikumiem Direktīvās 2014/30/ES, 2014/35/ES. Pilns ES atbilstības deklarācijas teksts ir pieejams šādā interneta vietnē: www.ubnt.com/compliance Lietuvių...