Electrical Safety - Stanley FATMAX SFMEH230 Manual De Instrucciones

When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Labels on tool
The following pictograms are shown on the tool , along with
:
the date code:
Warning! To reduce the risk of injury, the user
O
must read the instruction manual.
Wear safety glasses or goggles.
N
Wear ear protection.

Electrical safety

#
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
If the supply cord is damaged, it must be replaced by the
u
manufacturer or an authorised Stanley Fat Max Service
Centre in order to avoid a hazard.
Using an extension cable
Always use an approved extension cable suitable for the
power input of this appliance (see technical data).
The extension cable must be suitable for outdoor use and
marked accordingly. Up to 30 m of 1.5 mm2 HO5VV-F exten-
sion cable can be used without loss of product performance.
Before use, inspect the extension cable for signs of damage,
wear and ageing. Replace the extension cable if damaged or
defective. When using a cable reel, always unwind the cable
completely.
Features
This tool includes some or all of the following features.
1. Side handle
2. Switch
3. Electronic impact energy control dial
4. Chisel position index collar
5. Lube oil-injection inlet
6. Tool holder / sleeve
7. Side handle clamp knob
Electronic impact energy control
The electronic impact energy control (3) offers the following
advantages:
(Original instructions)
Use of smaller accessories without risk of breakage.
u
Minimised break-out when chiselling soft or brittle
u
materials.
Optimal tool control for precise chiselling.
u
Service reminder light
When the service reminder light (10) lights up or blinks, this
will indicate that the cut-out carbon brushes will switch off the
tool in approximately 8 hours. After that period, the light will go
off and the tool will stop running.The tool must then be sent to
a Stanley FatMax service center for service.
Soft start feature
The soft start feature allows the impact rate to build up
more slowly, thus preventing the chisel or point from
"bouncing"around on the masonry when starting up.
Assembly
Warning! To reduce the risk of injury, turn unit off and
disconnect machine from power source before installing and
removing accessories, before adjusting or changing set-ups or
when making repairs. Be sure the trigger switch is in the OFF
position. An accidental start-up can cause injury.
Inserting and removing SDS-Max accessories (Fig.
B, C)
This tool uses SDS-Max chisels (refer to the inset in FIG B
for a cross-section of a chisel shank). We recommend to use
professional accessories only.
Clean and grease the chisel shank.
u
Warning! Do not apply lubricant to themachine.
Insert the chisel shank into the bit holder/tool sleeve (6).
u
Press and turn the chisel slightly until the sleeve snaps
into position.
Pull on the chisel to check if it is properly locked. The
u
hammering function requires the chisel to be able to move
axially several centimetres when locked in the tool holder.
To remove a chisel, pull back the tool holder/ sleeve (6)
u
and pull the chisel out of the tool holder.
Warning! Always wear gloves when you change accessories.
The exposed metal parts on the tool and accessory may
become extremly hot during operation.
Indexing the chisel position (Fig. E)
The chisel can be indexed and locked into 12 different
positions.
Insert the chisel as described above.
u
Pull forward and rotate the chisel position collar (4) in the
u
direction of the arrow until the chisel is in the desired
position.
ENGLISH
5