Cequent Towing Products 75376 Instrucciones De Instalación

*
Will not fit models equipped with Air
Suspension Package
Hitch Shown In Proper Position Hitch Shown In Proper Position
Equipment Required: Sealant
Fastener Kit: 75376F or 87755F
Wrenches: 10mm, 16mm, 3/4
Drill Bits: ½"
Remove in
step 3.
Figure 1.
1
Qty. (4) ½ Hex Nut
2 2
Qty. (4) Conical Toothed Washer
3
Qty. (4) ½-13 X 1.75 GR5 Carriage Bolt
1. Remove the spare tire and the foam spare tire locator from the inside the vehicle.
2. Remove the fascia bolts and plastic fascia rivets from the fascia tabs. Remove the two rubber grommets from the trunk pan.
3. Remove the plastic fascia bracket shown in Figure 1. and the trunk pan cover shown in Figure2. and return to vehicle owner. Note: Trunk pan
cover may be trimmed and reinstalled if required.
4. Remove the four (2 per side) lower M10 nuts from the bumper brackets (do not discard).
5. Raise the hitch into position with side brackets installed on the bumper bracket bolts and loosely reinstall the M10 nuts removed in step 4.
6. From the inside of the vehicle install the carriage bolts and 1/4 X 1.00 X 3.00 blocks through the existing holes in the trunk pan and through the
hitch. Install the conical toothed washers and hex nuts as shown above.
7. From the underside of the vehicle, using the hitch as a template, drill the two ½" holes (1 per side) through the trunk pan.
8. From the inside of the vehicle install the carriage bolts and 1/4 X 2.00 X 3.00 blocks through the existing holes in the trunk pan and through the
hitch. Install the conical toothed washers and hex nuts as shown above.
9. Seal the holes in the trunk pan to prevent intrusion of exhaust fumes and water.
10. Place the spare tire carrier and spare tire back inside the vehicle and reinstall the fascia bolts removed in step 2.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2005, 2006, 2008, 2010 Cequent Towing Products
Installation Instructions
Mercedes-Benz ML350*
(will not fit 2010 & newer ML350 Blue-Tec models.)
Mercedes-Benz ML500*
Mercedes-Benz ML320 CDI*
Mercedes-Benz ML550* M
Fascia
Drilled Hole
Drilled Hole
Trunk Pan
Existing Nuts
Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N-M) Ti h ll ½ 13 GR5 f
Tighten all M10 fasteners with torque wrench to 38 Lb.-Ft. (52 N-M)
d B ML550*
Do Not Exceed Lower of Towing Vehicle Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV3, SUV4
Bumper Bracket
Existing
Hole
4
Qty. (2) ¼ X 1.00 X 3.00 Block
5 5
Qty. (2) ¼ X 2.00 X 3.00 Block
i h h
Sheet 1 of 3
Part Numbers:
Max Gross
Trailer WT (LB)
4000 (1 816 Kg)
3500 (1 589 Kg)
Remove in
step 3.
75 Lb F (102 N M)
75376N 12-7-10
75376
44534
87755
Max Tongue
WT (LB)
400 (182 Kg)
350 (159 Kg)
Figure 2.
Rev. D