Worx WG650 Manual De Instrucciones página 13

Quitanieves
Ocultar thumbs Ver también para WG650:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

found in the center of the Middle Handle
(10). Place the washer and screw on the
wing nut (See Fig. O, P).
NotE: do not overtighten the nut.
3. uSiNg thE PowEr cord hook (14)
(See Fig. Q)
in order to reduce strain on the power inlet
form a loop and hitch the extension cord
around the Power Cord Hook (14).
OPeRAtIOn
warNiNg! before using this
machine, make sure that the power
source you will use complies with the
specifications detailed in this manual.
before inserting the plug into the socket,
verify that the Snow thrower's rubber
plates are firmly secured with screws,
and that the rubber plates are facing the
correct direction. Perform a test run to
ensure that the auger (7) turns freely.
1. StartiNg aNd StoPPiNg
(See Fig. r, S)
StartiNg
Connect the plug to the power source and
switch ON.
the switch box is provided with a Lock-off
button to prevent accidental starting.
With one hand press and hold the Lock-Off
button (1), with the other hand pull the Switch
Lever (2) towards the handle, and release the
Lock-Off button. The machine is now started;
wait until the Auger (7) is at full speed before
working. Then use both hands to hold the
Switch Lever to keep it running.
StoPPiNg
Release the Switch Lever.
2. maNEuvEriNg thE SNow throwEr
aNd throwiNg SNow
warNiNg: Foreign objects, such as
rocks, broken glass, nails or wire,
can be picked up and thrown by the Snow
thrower, causing serious personal injury.
remove all foreign objects from the area
to be plowed before operating the Snow
thrower. Some objects may be hidden
Snow thrower
underneath the snow.
1) if the Snow Thrower hits an obstruction
or picks up a foreign object during use,
stop the Snow Thrower, disconnect the
extension cord, remove the obstruction,
and inspect the unit for damage. Repair or
replace any damaged part before restarting
and operating the unit.
2) Keep children, pets, and bystanders away
from the area of operation. be aware that
the normal noise of the machine when
turned on may make it difficult for you to
hear approaching people.
3) When moving the Snow Thrower, use the
wheels on one side as the pivot point.
Slightly tilt the Snow Thrower on this pivot
point to move it forward or backward.
4) Start your clearing path near the electrical
outlet and work outward, throwing snow
in a back and forth motion. To clear in the
opposite direction, step over the cord and
pivot the Snow Thrower on its wheels.
Make sure to overlap clearing paths.
5) Note wind direction. if possible, move in
the same direction as the wind so that the
snow is not thrown against the wind (and
thus back into your face and on the just
cleared path).
6) While moving the Snow Thrower, do not
drag the power cable violently or roughly.
The Snow Thrower should move within the
range that the cable can reach.
7) Do not push the Snow Thrower with
excessive force. You should push the
machine gently and evenly in accordance
with the unit's throw rate.
8) Do not apply additional man-made load to
the tool as this may cause damage to the
motor.
9) Some parts of the Snow Thrower may
freeze under extreme temperature
conditions. Do not attempt to operate the
Snow Thrower with frozen parts. if the
parts freeze while the Snow Thrower is in
use, stop the Snow Thrower, unplug the
extension cord, and inspect for frozen
parts. Free all parts before restarting or
operating the Snow Thrower. Never force
controls that have been frozen.
10) Working on pebbles, gravel, or unpaved
13
en

Publicidad

Tabla de contenido
loading

Tabla de contenido