Harman JBL MS-A1004 Guia Del Usuario página 10

10
To Set the Input Level:
1. Move the switch for the Input Signal Selector to the Hi position (or Hi2, if you are connecting to a factory
system with open-circuit protection).
2. Set the bass, treble, balance and fader controls on your head unit to the center (or flat) positions. Set
loudness to off. Defeat any sound-enhancement (such as DSP, surround sound or EQ) settings.
3. Insert the setup CD into your head unit and verify that the CD is playing.
4. Enter Setup mode by pressing CW and CCW buttons simultaneously for more than three seconds until
the Input Level adjustment icon
cator will show " " in the display).
5. Turn the head unit's volume control all the way up (to maximum output).
6. Using a small screwdriver on the level-adjustment dial next to the Input Signal Selector switch,
adjust the Input-Level Control up or down, while watching the icons on the amplifier's display panel.
If the green "up" arrow
If the red "down" arrow
is lit.
NOTE: If turning the control fully clockwise doesn't cause the
the Input Signal Selector to the Lo position and try again.
Once the icon is lit, stop adjusting and repeat the procedure to set the input level on the other channels.
When both check marks are lit, the input levels for each channel pair are set properly.
To Enable or Disable Signal-Sensing Turn-On:
7. While in Setup mode, enable/disable signal-sensing turn-on
by turning the rotary controller clockwise or counterclockwise
to select SEn On or SEn OFF in the display. If you have
connected a remote turn-on lead, set to SEn OFF.
8. Turn the volume control on your head unit down and remove the
setup CD. If you miss or circumvent this step, the audio system
will reproduce a loud test signal that could damage speakers when exiting the Setup mode.
9. Press and release the CW and CCW buttons simultaneously to exit Setup mode.
10. Do not adjust the Input-Level Controls further. Use the Output Gain Control to balance the channel levels
and to "tune" the system.
SETTING THE FILTERS (CROSSOVERS)
There are 98 selectable frequencies for the low-pass and high-pass
filter settings. The selectable frequencies are detailed in the table to the
right.
Getting to the Crossover Settings
Press both CCW and CW buttons at the same time for less than three
seconds and release, to activate the controls. Use the CCW and CW
buttons to navigate to the preferred crossover-adjustment parameter.
How to Set a High-Pass Filter
Navigate to the high-pass filter frequency parameter
rotary encoder, select the desired cutoff frequency. Then navigate to
the high-pass filter slope parameter
select the desired filter slope.
High-Pass Example
Use the CW and CCW buttons to navigate to the Low-Pass frequency
parameter and set to OFF.
How to Set a Low-Pass Filter
Navigate to the Low-Pass Filter frequency parameter
cutoff frequency. Then navigate to the Low-Pass Filter slope parameter
select the desired filter slope.
Low-Pass Example
Use the CW and CCW buttons to navigate to the High-Pass frequency parameter and set to OFF.
lights. The amplifier's output will be muted (the output-level indi-
icon is lit, turn the control clockwise until the
icon is lit, turn the control counterclockwise until the
Mode
SEn On
SEn OFF
Available Crossover Frequency Settings
20.0Hz
22.5Hz
25.0Hz
27.5Hz
30.0Hz
32.5Hz
35.0Hz
37.5Hz
40.0Hz
42.5Hz
and, using the
45.0Hz
50.0Hz
and, using the rotary encoder, 55.0Hz
and, using the rotary encoder, select the desired
icon is lit.
icon
icon to light, move the switch for
Function
Signal Sensing is ON
Signal Sensing is OFF
95.0Hz 260Hz 1.40kHz
100Hz 270Hz 1.50kHz
105Hz 280Hz 1.60kHz
110Hz 290Hz 1.70kHz
115Hz 300Hz 1.80kHz
120Hz 350Hz 1.90kHz
125Hz 400Hz 2.00kHz
130Hz 450Hz 2.20kHz
140Hz 500Hz 2.40kHz
150Hz 550Hz 2.60kHz
160Hz 600Hz 2.80kHz
170Hz 650Hz 3.00kHz
180Hz 700Hz 3.20kHz
60.0Hz 190Hz 750Hz 3.40kHz
65.0Hz 200Hz 800Hz 3.60kHz
70.0Hz 210Hz 900 Hz 3.80kHz
75.0Hz 220Hz 1.0kHz 4.00kHz
80.0Hz 230Hz 1.10kHz 4.20kHz
85.0Hz 240Hz 1.20kHz 4.40kHz
90.0Hz 250Hz 1.30kHz 4.60kHz
and, using the rotary encoder,
4.80kHz
5.00kHz
5.50kHz
6.00kHz
6.50kHz
7.00kHz
7.50kHz
8.00kHz
8.50kHz
9.00kHz
9.50kHz
10.0kHz
12.0kHz
14.0kHz
16.0kHz
18.0kHz
20.0kHz
OFF