Certification And Safety Approvals; Glossary - Jabra BT110 Manual Del Usuario

10

Certification and safety approvals

FCC
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause
undesired operation.
Users are not permitted to make changes or modify the device in any way. Changes or
modifications not expressly approved by Jabra (GN Netcom) will void the user's
authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the
following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
The user must place the base 8" (20cm) or more from any personnel in order to comply
with FCC RF exposure requirements.
Industry Canada
Operation is subject to the following two conditions: (1) This device may not cause
interference and (2) This device must accept any interference, including interference
that may cause undesired operation of the device.
The term "IC:" before the certification/registration number only signifies that
registration was performed based on a Declaration of Conformity indicating that
Industry Canada technical specifications were met. It does not imply that Industry
Canada approved the equipment.
10
CE
This product is CE marked according to the provisions of the R & TTE Directive (99/5/EC).
Hereby, GN Netcom, declares that this product is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
For further information please consult http://www.gnnetcom.com
Please note that this product uses radio frequency bands not harmonised within EU.
Within the EU this product is intended to be used in Austria, Belgium, Denmark, Finland,
France, Germany, Greece, Ireland. Italy, Luxembourg, The Netherlands, Portugal, Spain,
Sweden, United Kingdom and within EFTA in Iceland, Norway and Switzerland.
Bluetooth
The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use
of such marks by Jabra is under license. Other trademarks and trade names are those of
their respective owners.
11

Glossary

1
Bluetooth is a radio technology developed to connect devices, such as mobile
phones and headsets, without wires or cords over a short distance of up to 10 metres
(approx 30 feet). More information is available at www.bluetooth.com
2
Bluetooth profiles are protocols through which Bluetooth devices communicate
with other devices. Your phone needs to support either the handsfree or headset
profile to function with the Jabra BT110.
3
Pairing creates a unique and encrypted communication link between two Bluetooth
enabled devices and allows them to communicate with each other. Bluetooth devices
will not work if the devices have not been paired with each other.
4
Passkey or PIN is a code that needs to be entered on the phone in order to pair the
mobile phone with the Jabra BT110. When you have already paired your mobile
phone with the headset, the phone and the Jabra BT110 will recognize each other
and the phone will bypass the discovery and authentication process and
automatically accept the transmission.
5
Standby mode is when the Jabra BT110 is used with the Jabra A210 and is passively
waiting for a call. When you "end" the call on your mobile phone, the headset will
go into standby mode. The yellow LED will indicate standby mode by flashing every
3 seconds.
11