Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Workpiece :
- Remove nails and clean the workpiece before
cutting! Nail, sand or foreign matter can
cause blade damage or cause severe danger to the
user.
Machine:
- Check before operation that the dust expel
opening is not obstructed.
- Do not remove chips from the chip chute when
the motor is running. Clean out chips after
the blades come to a complete stop. Always use a
stick etc. when cleaning them out.
- Do not leave the tool running. Wait until it has
come to a complete stillstand.
- To avoid risk of overheating or jamming, never
force the tool.
- Always fasten your machine to a workbench:
before starting any work, check the stability
of your machine..
Residual risks
- These risks are present during operation,
remain vigilant.
- Danger of injury to fingers or hands while
changing the blade; wear gloves.
- Danger of injury caused by ejected debris;
wear safety glasses.
- Danger to hearing; wear safety ear muffs
- Risk of inhaling airborne particles; wear a dust
protector mask.
Caution: sawdust and wood chips
can cause allergies and injury.
Fires and explosions
can be triggered if oxygen from the
air and a source of ignition are also
1. Always wear eye protection goggles when
using
2. Never make planer depth more han 2.5mm
3. Never use the tool without the protectors in
place.
4. Never use the tool without the protectors in
place.
5. Never make planer depth more han 2.5mm
6. Do not planer wood with nails or other wood that
could damage the knife.
7.
Do not planer wood less than 200mm long,
20mm broad or 7 mm thickness.
8.
Make sure the blades installed correctly before
starting
9.
If the wood thickness is less than 75mm,
please use a push stick.
10. Do not get your hands near the dust pipe.
11. Never let the tool working without surveillance.
12. The appliance can only be used when it is fixed
properly on the workbench.
13. Do not put the wood in the opposite direction
14. When mounting the appliance or change the
knifes, belt or brush, the switch must be turned
OFF (0) and the power plug must be
unplugged.
15. Touching of the spinning knife driving shaft
causes serious injuries and lose limbs. Any
present.
part of the knife driving shaft that is not
used for planing must be covered!
16. Manufacturing processes other than those
recommended can lead to dangerous
situations. The surface planing machine is
intended only for planing wooden boards and
wooden planks with assigned minimum
measure!
17. Machines that are not maintained can lead to
uncontrolled situations. Regularly control the
machine, the height stop and the correct
placement of the knife on the knife driving shaft
before every usage.
18. Wood dust can present a hazard to health.
Aspirating the wood dust can cause diseases
resulting in death.
19. knife driving shaft and height stop have to be
repaired immediately when damaged
20. Wood longer than 1m is not suitable for this
machine.
21. Wood with uneven surface is not suitable for
this machine.
A. COMPONENTS
1. Unadjustable working table
2. Protective cover
3. Fence
4. Adjustable working table
5. Height adjustment handle
6. Switch
7. Bit gauge
8. Protective cover lock knob
9. Current protector
10. Directin plate(left+right)
11. Dust pipe
12. Belt cover plate
13. Rubber feet
14. Open wrench
15. Pointer
B·ASSEMBLY
1. Unpack the machine and installed four rubber feet(13) in
the buttom of four corners
2. Fix the dust pipe (11) with three cross recess
self – tapping screws
3. Tighten the protective cover lock knob (8)to
the protective cover (2）
C. INSTALLATION
Before the installation set the switch to （O） and
unplug the machine from power supply.
D-1. Angular deflection of stop bar
To set the angle of the stop bar loosen the left and
right height adjustment (11), set the angle you wish
and screw the height adjustment. Check with a
triangle if the angle is correct.
21
Publicidad
Tabla de contenido
