Publicidad
Idiomas disponibles
Idiomas disponibles
Always wear SAFETY GLASSES
when installing hitch
Figure 2
Trim bumper for
needed for fascia
clearance. Both sides
Rear
Scan for step by step
PHOTO installation
instruction or visit
http://www.cequent
group.com/qr-
Note: Fasteners typical both sides
product.aspx
1.
Mark centerline of fascia with marker or tape.
Remove plastic rivets and screws: Remove plastic rivets from supports on bottom of bumper fascia. Rivets are released by first pulling out center post of rivet approx 1/4". Rivet can then be pushed out
2.
by hand. Remove the Philip screw ( approx. 3 each side).
Open trunk: Open trunk to remove the hex screw (2) from under the rear hatch securing the bumper fascia. Repeat for each side.
3.
Bumper fascia removal; Loosen the tail lights bolts for additional clearance, during fascia removal. Gently pull up from the rear wheel well trim panel each side, unclipping the tabs inside. Work up to
4.
taillights and continue to gently remove along the bottom of the tail lights. Using a small screwdriver lift cl eats between the fascia and tail lights if needed. Continue to remove along inside bottom to
the trunk, if needed, use a small flat screw driver to release the cleats at the top of the fascia while carefully pulling the fascia away from the vehicle. If present disconnect any wiring harness at the fascia,
and put the fascia cover aside.
Bumper removal: Remove the (8) bolts holding the bumper in place and return the fasteners to the owner.
5.
Bumper trimming: using a die grinder remove the material shown in Figure 2. Both sides
6.
Hitch installation: Raise the hitch and bumper into position as shown, and attach using the fasteners provided.
7.
8.
Tighten all M8 CL8.8 fasteners with torque wrench to 20 Lb.-Ft. (27 N*M).
Trim fascia: using the center of the fascia marked in step 1.
9.
10. Reinstall fascia: starting from the center of the vehicle lineup and gently reinstall the rear fascia and all fasteners in reverse order steps 2-4. (Note: reattach any wiring hardness if removed)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry of water and exhaust fumes. A hitch or
ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684.
©2016 Cequent™ Performance Products, Inc. -
Installation Instructions
PART NUMBERS: 24946, 77333, CQT24946
(Sold separately)
Drawbar Kit: 3593
Drawbar must be used in
the RISE position only.
End panel
Figure 1
① ②
Proper torque is needed to keep the hitch secure to the vehicle when towing.
2.50 x 4.125 off center mark. Use drill to create radius. See Figure 3.
Printed in Mexico
F A S T E N E R
①
②
2.50 X 2.50 cutout in fascia required.
Use drill to create radius.
Existing weld nuts
Located on opposite
side of end panel
Sheet 3 of 18
24946NP
K I T :
2 4 9 4 6 F
Qty. (8)
Hex bolt
M8 X 1.25 X 30 CL8.8
Qty. (8)
Conical washer
3/8''
Figure 3
Fascia trimming
Concial washer
teeth side
against hitch
6-17-16
Rev. A
Publicidad
