Publicidad
Operating and Care Instructions for HB18 Labeler
Thank you for purchasing the HB18 Hubert
®
Labeler. For best results please read the instructions completely before operating the Labeler .
G
T
LOSSARY OF
ERMS
1.
Price band housing
8.
Label feeding roller
2.
Print adjustment screw
with sprocket spindles
3.
Ink roller
9.
Operating lever
4.
Label dispensing roller
10. Label spindle
5.
Base plate cover
11. Labels
6.
Base Plate
12. Label roll cover
7.
Base plate open lever
placa de base
12
11
1
12
11
1
10
10
9
9
2
2
8
8
3
3
4
4
7
7
6
6
5
5
B
L
AND
AYOUT
This gun is
designed not only
for product pricing,
but also can
accommodate
your date - coding
and PLU
identification
needs.
H
C
OW TO
HANGE
P
/ D
C
RICING
ATE
ODING
Pull or push the dial shaft, A, to the desired
band and rotate the shaft in either direction.
When desired pricing or date configuration
is set, push the dial shaft inward to lock
bands in place.
A
Hubert
®
guarantees the HB18 Labeler when used under normal working conditions. If this
product does not meet your expectations please call us at 1-800-543-7374 for a complete and timely
resolution.
A
P
DJUSTING THE
RINTING
1. Using a Phillips head
screwdriver, turn screw
to the left and slide
screw to desired position.
2. Tighten screw in new
position.
1 2 3 4 5 0
1 2 3 4 5 0
For upper-position
For center-position
For below-position
printing
printing
H
C
I
R
OW TO
HANGE THE
NK
OLLER
1. Press and pull out A to open the ink roller case.
A
OLD
2. Grab hold on the
3. Gently pull the
exposed lever and raise
sides of the carrier
the ink roller carrier up
apart to release the
and out of the Labeler.
old ink roller.
NEW
4. Snap new ink roller
5. Snap cover,
into carrier and replace
A, closed.
carrier to original
location in gun.
N N O O T T E E : :
Try to hold new ink roller by the outermost rim of
carrier to reduce transference of ink onto your fingers.
O
G
UR
UARANTEE
1. Pull up on label cover
as illustrated.
P
OSITION
2. Pull back on black
base plate levers
located on each side
1 2 3 4 5 0
of the labeler. Release
levers once base plate
and base plate cover
opens.
printing
3. Insert label roll, labels
facing up.
4. Insert label roll into Labeler
housing at a slant / on an
angle, as shown.
5. Straighten roll into an upright
position on spindle.
T
S
ROUBLE
HOOTING
Problem:
Labels are not advancing
Printing is too light on one side of the label
Numbers not printing clearly
Printing looks too high/low on labels
Printing hits between two labels
For replacement labels and ink rollers contact us at:
H
L
OW TO
6. Feed labels directly
through center of labeler,
between base plate and
plate cover. Allow
several inches of labels
to extend out of
the bottom.
7. Snap
base
plate
closed.
8. Line up holes on label strip with spindle sprockets
9. Snap the base plate cover closed, taking care
not to detach label strip from roller.
10. Squeeze and release the operating lever
several times to dispense labels
Check the following:
Make sure sprocket spindles and label feeding roller are advancing.
Clean off any adhesive buildup on the sprocket spindles.
Make sure the ink roller and ink roller carrier are making contact with the bands.
Make sure the ink roller and ink roller carrier are fixed securely in place.
Clean the bands with a soft, dry brush. Lint mixing with ink will create a
buildup on and around the characters on the bands; or replace ink roller.
See section on adjusting printing position.
Reload the labels for correct alignment on the sprocket spindles.
L
OAD
ABELS
Base Plate
Base Plate Cover
Publicidad
