Electrical Safety Rules; Fire Hazard Safety Rules; Induction Heater Safety Rules - BGS technic 2169 Manual De Instrucciones

Electrical Safety Rules


Do not fit or remove a coil, rope coil or Body Pad with the INDUCTION HEATER plugged into the
mains.

Before plugging in the INDUCTION HEATER, make sure that the outlet voltage supplied is
compatible with the voltage marked on the label and within 10% of the stated voltage. An outlet
voltage incompatible with that specified on the label can result in serious hazards and damage to
the INDUCTION HEATER.

Ensure the INDUCTION HEATER is connected to a supply that is adequately earthed.
(Grounded)

Do not use the INDUCTION HEATER in the rain, moisture or immersed in water. Exposing the
INDUCTION HEATER to water or other liquids can cause an electrical shock hazard.

Do not use any attachments except for those supplied by BGS, use of non approved attachments
may cause damage to the INDUCTION HEATER and invalidate your warranty.

Do not leave the INDUCTION HEATER plugged into the mains when not in use.
Electrical Safety Rules

Damaged cords create electric shock hazards - Do not kink, bend, crush or cut the mains
electrical lead. Never carry the INDUCTION HEATER by the mains electrical lead.

Keep the lead away from heat, oil, sharp edges and/or moving parts. Do not use the INDUCTION
HEATER if the lead is damaged. Leads cannot be repaired, only replaced.

Do not use any attachment with damaged insulation, use of damaged attachments can result in
sparking and can cause a fire hazard. Use of damaged attachments will invalidate the warranty.

THE INDUCTION HEATER SHOULD NOT BE USED CONTINUOUSLY FOR MORE THAN ONE
MINUTE ON ANY MATERIAL

Fire Hazard Safety Rules


It is dangerous to heat paint/ aerosol cans, or any other pressurised or sealed containers used for
storing fuels, compressed gases, and liquids. The heat generated by the INDUCTION HEATER
can cause these containers to explode and their contents to ignite. Do not attempt to heat these
items using the INDUCTION HEATER

Do not use an attachment if the insulation has been breached. If insulation has been breached it
can cause sparking when contacting with a vehicle. This could be a fire hazard especially when
working on, or near fuel lines and/or fuel tanks.

Use of damaged attachments will invalidate the warranty.

INDUCTION HEATER Safety Rules


Do not use the INDUCTION HEATER without an attachment fitted. Ensure attachment is securely
located and thumb screws are firmly tightened.

Do not use the INDUCTION HEATER for longer than the stated duty cycle: ONE minute on
followed by ONE minute off.

The main circuit board has an overheat protection device, however the attachments do not have
overheat protection so should not be used for more than ONE minute of continued use.

Please ensure that the cooling fan is running when the power switch is operated, if the fan does
not run DO NOT use the INDUCTION HEATER and contact BGS

Do not attempt to create more than 4 coils using a "YOU-FORM" or rope coil, a minimum of 2 coils
and a maximum 3 to 4 coils is the optimum number needed for best operation.

The INDUCTION HEATER should not be left unattended whilst switched on.

In order to cool effectively, and prolong the life of your INDUCTION HEATER, always ensure that
there is a sufficient supply of clean air, Make sure that the vents of the INDUCTION HEATER are
clean and free of dust and debris so that the Power Unit has an unimpeded flow of cooling air.

Do not attempt to repair or service the INDUCTION HEATER. There are no User-serviceable
BGS technic KG
Bandwirkerstr. 3
D-42929 Wermelskirchen
3
Tel.: 02196 720480
Fax.: 02196 7204820
mail@bgs-technic.de
www.bgstechnic.com
© BGS technic KG, Copying and further use not allowed