Kettler Golf E Manual De Instrucciones página 4

Handling the equipment
Before using the equipment for exercise, check carefully to ensure
that it has been correctly assembled.
Before beginning your first training session, familiarize yourself
thoroughly with all the functions and settings of the unit.
It is not recommended to use or store the apparatus in a damp room as
this may cause it to rust. Please ensure that no part of the machine comes
in contact with liquids (drinks, perspiration etc.). This may cause corrosion.
The machine is designed for use by adults and children should
not be allowed to play with it. Children at play behave unpre-
dictably and dangerous situations may occur for which the manu-
facturer cannot be held liable. If, in spite of this, children are
allowed to use the equipment, ensure that they are instructed in
its proper use and supervised accordingly.
The exercise cycle complies with the DIN EN 957 - 1/5, class
HB. It is therefore unsuitable for therapeutic use.
A slight production of noise at the bearing of the centrifugal mass
is due to the construction and has no negative effect upon ope-
ration. Possibly occurring noise during reverse pedalling result
from engineering and are absolutely safe.
nstructions for Assembly
Ensure that you have received all the parts required (see check
list) and that they are undamaged. Should you have any cause
for complaint, please contact your KETTLER dealer.
Before assembling the equipment, study the drawings carefully
and carry out the operations in the order shown by the diagrams.
The correct sequence is given in capital letters.
The equipment must be assembled with due care by an adult
person. If in doubt call upon the help of a second person, if pos-
sible technically talented.
Please note that there is always a danger of injury when working
with tools or doing manual work. Therefore please be careful
when assembling this machine.
Ensure that your working area is free of possible sources of danger, for
example don't leave any tools lying around. Always dispose packaging
material in such a way that it may not cause any danger. There is always
a risk of suffocation if children play with plastic bags!
The fastening material required for each assembly step is shown
in the diagram inset. Use the fastening material exactly as
instructed. The required tools are supplied with the equipment.
List of spare parts
When ordering spare parts, always state the full article number, spare-part
number, the quantity required and the inspection number stamped on the back.
Example order: Art. no. 07961-800 / spare-part no. 10100030/ 2
pieces / inspection no......
Important: spare part prices do not include fastening material; if fastening
material (bolts, nuts, washers etc.) is required, this should be clearly stated on
the order by adding the words „with fastening material".
4
Do not use corrosive or abrasive materials to clean the equipment.
Ensure that such materials are not allowed to pollute the envi-
ronment.
The exercise cycle has a magnetic brake system.
To operate correctly, the pulse function requires a minimum
voltage of 2,7 volts (only for computers working with batteries).
The equipment is dependent of revolutions per minute.
Please ensure that liquids or perspiration never enter the machine
or the electronics.
Before use, always check all screws and plug-in connections as
well as respective safety devices fit correctly.
Always wear suitable shoes when using.
All electric appliances emit electromagnetic radiation when in
operation. Please do not leave especially radiation-intensive
appliances (e.g. mobile telephones) directly next to the cockpit
or the electronic controlsystem as otherwise values displayed might
be distorted (e.g. pulse measurement).
Bolt all the parts together loosely at first, and check that they have
been assembled correctly. Tighten the locknuts by hand until resis-
tance is felt, then use spanner to finally tighten nuts completely
against resistance (locking device). Then check that all screw con-
nections have been tightened firmly. Attention: once locknuts have
been unscrewed they no longer function correctly (the locking
device is destroyed), and must be replaced.
To pull off the pedal arms remove cap and screw (A). Grip the
pedal arm tightly, and screw in an M12 bolt (not supplied) into
the thread (B). After a few turns you may take off the pedal arm
(C).
For technical reasons, we reserve the right to carry out prelim-
inary assembly work (e.g. addition of tubing plugs).
Please keep original packaging of this article, so that it may be used
for transport at a later date, if necessary.
KETTLER (GB) Ltd. · Merse Road · North Moons Moat · Redditch,
Worcestershire B98 9HL · Great Britain
KETTLER International Inc. · 1355, P. B. 2747 · Virginia Beach · VA
23450 USA
http://www.kettler.net
).)