Initial Battery Charge; Battery Replacement; Battery Recharge - Peg-Perego LIL TRACTOR & Trailer Empleo Y Manutencion

INITIAL BATTERY CHARGE

!• Remove battery and charger from packaging. Connect battery charger to a 120vac wall recepticle. Connect battery charger to battery.
CAUTION:
ADULT ASSEMBLY REQUIRED.
USE CARE WHEN UNPACKING AS COMPONENTS TO BE ASSEMBLED MAY POSE A SMALL PARTS/SHARP EDGE
HAZARD.
BATTERY IS INCLUDED AND MUST BE CONNECTED;
1 • Unscrew the 2 knobs under the seat.
2 • Position the seat as shown in the figure.
3 • IMPORTANT: the seat can be adjusted to 2 positions depending on the height of the child (see figure). Position 1: the seat is higher and further back. Position
2: the seat is lower and further forward.
4 • Turn the vehicle on its side, keeping the seat in position. Remove the screw from the access door, under the vehicle.
5 • Open the cover to access the seat attachment knobs.
6 • Screw on the two seat knobs as shown in the figure. Close and screw on the cover.
7 • Snap on the 2 rear light lenses.
8 • Assemble the indicators as shown in the figure.
9 • Attach the 2 indicators at the front of the vehicle, as shown in figures 1-2, taking care that the hollow part of the indicator is facing down.
10 • Press on the 2 headlight lenses as shown in detail A.
11 • Position the steering wheel. Attach the steering wheel with the screw (10P x 1
12 • Push on the steering wheel cap as shown in the figure.
13 • Insert one of the 4 self-locking washers (the tractor comes with 2 spare washers) into the special tool provided with the tractor. ATTENTION: the tabs on the
self-locking washer must be turned towards the interior of the tool (see detail A).
14 • Remove the axle from the packing. Remove the protective caps from the axle. Insert the axle by pounding the special tool all the way in using a hammer.
Remove the tool.
15 • Slide the 2 wheels onto the axle. IMPORTANT: check that the wheels are correctly inserted, with the hub caps facing out.
16 • Place a self-locking washer in the special tool, and insert the prepared axle, pounding it all the way in.
17 • Attach the wheel unit to the base of the trailer by pressing on it.
18 • Attach the bottom of the trailer (prepared beforehand) to the bed by pressing, as shown in the figure.
19 • Assemble the 3 sides of the trailer, ensuring that the parts with the wooden effect are facing outwards.
20 • Fit the assembled parts into the slots in the base of the trailer.
21 • Insert the red coupling into the hole on the trailer (see figure).
22 • Couple the trailer onto the back of the tractor, rotating the red lever. Figure 1: the trailer can be uncoupled; figure 2: the trailer coupled. WARNING: The
trailer will hold a load weighing up to 11 lbs (5 kg).
23 • Attach the 2 hubcaps to the wheels on the trailer (Attention, in the packaging you will find 6 hubcaps; the remaining 4 are to be attached to the wheels of the
tractor).
24 • Unscrew the hood.
25 • Pull the hood towards you while lifting and turning it to remove (see figure).
26 • Connect the battery plug to the electric system plug.
27 • Close the hood, taking care to correctly insert the tabs into the openings in the chassis. ATTENTION: Detail A shows the hood incorrectly attached. The
vehicle is ready for use.
28 • ACCELERATOR PEDAL/ELECTRIC BRAKE: when the foot is lifted from the accelerator pedal, the electric brake automatically stops the tractor.
WARNING:
WARNING: BATTERY CHARGING AND ANY OTHER OPERATION ON THE ELECTRICAL SYSTEM MUST BE
CARRIED OUT BY ADULTS ONLY.
THE BATTERY CAN ALSO BE CHARGED WITHOUT REMOVING IT FROM THE VEHICLE.
29 • Unscrew the hood.
30 • Pull the hood towards you while lifting and turning it to remove (see figure).
31 • Loosen the 2 screws that hold the battery in place.
32 • Disconnect the 2 plugs and remove the battery supplied with the vehicle.
33 • Insert a new battery and connect the two plugs.
34 • Screw the battery clamp into place again, turning it upside down as shown in the figure. Close the hood as described above (fig. 27) and fasten with the screw.
35 • Unplug vehicle wiring terminal A from battery terminal B, by pressing terminals on side and pulling apart.
36 • Plug the battery charger terminal to a wall outlet following the instructions enclosed. Connect the plug B to the battery charger plug C.
37 • Once the charge is completed unplug recharger from wall outlet. Unplug recharger cord terminal C from battery terminal B.
38 • Plug battery terminal A into vehicle wiring terminal B. Close hood.
ASSEMBLY INSTRUCTIONS
1/4
VEHICLE FEATURES AND INSTRUCTIONS FOR USE

BATTERY REPLACEMENT

BATTERY RECHARGE

inch) and washer (5 x 11 x 1 mm) provided.