Initial Battery Charge; Removing The Battery - Peg-Perego FIUS1201G169 Manual Del Usuario

INITIAL BATTERY CHARGE

!• Remove battery and charger from packaging. Connect battery charger to a 120vac wall recepticle. Connect battery charger to battery.
CAUTION:
ADULT ASSEMBLY REQUIRED.
USE CARE WHEN UNPACKING AS COMPONENTS TO BE ASSEMBLED MAY POSE A SMALL PARTS/SHARP EDGE
HAZARD.
BATTERY ALREADY INSTALLED IN VEHICLE.
1 • Apply the silver stickers to the special areas on the front headlights.
2 • Position the headlight lens by attaching the outer side.
3 • Press as shown in the figure to snap the lens into place.
4 • Repeat this step for the other front headlight.
5 • Position one of the two parts of the counterweight on the front of the tractor.
6 • Join the other part of the weight by pressing the two parts together.
7 • Press the side inserts into place on the body.
8 • Press the trim piece into place under the steering wheel.
9 • Push the steering column through the bottom of the tractor to the upper part of the body.
10 • Hold the column in place and slip the steering wheel onto it.
11 • Fasten the steering wheel with its screw and nut, being careful to insert the screw into the circular hole and to screw the nut onto the hexagonal part.
12 • Apply the silver stickers to the special areas on the rear taillights as shown in the figure.
13 • Attach the taillights by pressing from the bottom upwards.
14 • Unscrew the knobs on the bottom of the seat.
15 • Line the seat up with the two holes on the seat support.
16 • The seat can be adjusted to 2 positions to suit the height of the child (see figure).
17 • After adjusting the seat, tighten the 2 knobs that hold it in place.
18 • Position the seat support on the body of the tractor.
19 • Reposition the seat support on the body of the tractor and tighten the 2 screws.
20 • Position the roll bar (see figure).
21 • Push the roll bar all the way in.
22 • Tighten the 2 lock screws.
23 • Press the gas tank cap into place on the back of the tractor.
24 • Insert the plugs in the handlebar.
25 • Insert and fit the scoop dump control with the screws provided.
26 • Attach the bucket to the loader frame as shown in figure A. Fasten the pieces together with screws and nuts, working with the supplied wrench and a
screwdriver from the side shown in the figure.
27 • Partially insert the second screw on the opposite side, to make it easier to carry out the next operation.
28 • Insert the spring into the hole in the bucket block. Turn the spring while pressing downward (see side diagram).
29 • Push the screw into the spring. Place a washer and a nut on the screw, following the order shown in the diagram. Test by moving the bucket dump lever to see
if bucket automatically returns to the up position.
30 • Tighten the screw, using the supplied wrench and a screwdriver.
31 • Slip the bucket linkage rod through the special hole on the shovel.
32 • Place a stud in the special tool that comes with the toy, as shown in the diagram.
33 • Fasten the bucket linkage rod by pressing the stud all the way in.
34 • Using the two wrenches, unfasten one of the two lock nuts on the bucket linkage rod, as shown in the figure.
35 • Slip out the bucket linkage rod with the washer (A), taking care not to lose it.
36 • Apply decal No. 5R and No. 5L. Loosen the two safety screws from the sides of the hood, and remove the two plastic disks (save the disks for putting the
hood back on).
37 • Press the two buttons and at the same time widen the hood to detach it, as shown in the figure.
38 • Lift the hood off.
39 • Attach loader to hood.
40 • NO: The hood is not fastened.
OK: The hood is correctly fastened.
41 • Align the loader frame holes with the holes in the hood.
42 • Replace the attachment rod (with the washer) you removed before, passing it out the opposite part of the hood.
43 • Fasten the attachment rod with the second washer and the nut removed before.
44 • Tighten the nut using the two wrenches supplied with the toy, as shown in the figure.
WARNING:
WARNING: BATTERY CHARGING AND ANY OTHER OPERATION ON THE ELECTRICAL SYSTEM MUST BE
CARRIED OUT BY ADULTS ONLY.
THE BATTERY CAN ALSO BE CHARGED WITHOUT REMOVING IT FROM THE VEHICLE.
45 • Insert the battery charger plug into an electrical outlet, following the instructions that come with the charger. Connect point B to point C on the battery
charger.
When the battery has been completely recharged, disconnect the battery charger from the electrical outlet, and disconnect point C from point B.
46 • Insert point B into point A, pressing until it clicks into place. Always remember to close and fasten the cover on the battery compartment when you have
finished working on the battery.
47 • Reposition the hood by inserting the front hook into the opening on the bottom of the tractor (see detail).
48 • Slightly widen the hood, and lower it to its original position.
49 • Replace the two plastic disks and fasten everything down with the screws.
50 • GEAR SHIFT LEVER. The vehicle has 3 speeds. ATTENTION: when the vehicle is taken out of the box, it runs only in first gear and reverse gear. To use the
second speed, follow the instructions in figure 51.
51 • Loosen the lock screw for the second speed (fig. A). Turn the lock screw to the next notch (fig. B), and tighten it. All of the gears are now ready for use.
52 • ACCELERATOR PEDAL/ELECTRIC BRAKE. When the foot is lifted from the accelerator pedal, the electric brake automatically stops the tractor.
53 • To tip the shovel, lower the command lever.
54 • To lower the entire bucket block, push the handle forwards.complete, lift the foot off the accelerator pedal and release the gear lever.
55 • Unscrew the two safety screws from the hood. Remove the hood. Disconnect the battery from the electrical sistem by squeezing the sides of the plugs.
56 • Loosen the 2 screws on the battery brace, has shown in the figure.
57 • Remove the battery.
58 • Remove the battery clamp from the dead battery and put it on the new battery.
ASSEMBLY INSTRUCTIONS
BATTERY RECHARGE
VEHICLE FEATURES AND INSTRUCTIONS FOR USE

REMOVING THE BATTERY