SUHNER ROTOmaster Manual Tecnico página 5

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

loaded pin B3 clicks into place.
3.3 Connect the SAK safety clutch (
Machine elements
C1 Retention hole
C3 Locking pin
C2 Safety lever
C4 Spring-loaded pin
Use the Type «SAK» safety clutch to protect operator from accidental
start-up.
1. Insert casing coupler B8 into tool connection.
2. Depress spring-loaded pin B7 and completely insert casing
coupler B8.
3. Spring-loaded pin B7 must click audibly into place in retention
hole C1. Ensure that spring-loaded pin B7 has locked firmly into
place. If necessary, move/rotate casing coupler B8 until spring-
loaded pin B7 clicks into place.
3.4 Connect toolholders
(Fig. C)
The connection of toolholders corresponds to the procedure descri-
bed in Item 3.3.
Note: Toolholders TALM, TAM, FSM and SAM can be rotated on the
casing coupler B8 for easier handling.
3.5 Start-up with SAK safety clutch
(Fig. D)
Attention: The powerfull machine develops a heavy torque when swit-
ched-on. Thus secure yourself in a rigid position and hold on to the
handpiece.
Only with machine in OFF position! A1
1
Depress locking pin C3.
2
Completely depress safety lever C2. If necessary, move to starting
position by turning the working spindle D1 and repeatedly depres-
sing safety lever C2.
• Switch on drive motor A1.
• Switch off by releasing lever C2. Torque transmission to the
toolholder is interrupted. Locking pin C3 protects from automatic
start-up.
• Switch machine off in order to return safety lever C2 to starting
position!
4.0 Accessories
Important informatory sign. Toolholder maintenance: General
• Clean off grinding dust daily.
• Do not immerse in liquid.
• Bearings are greased for life.
• Change gear grease every 12 months (your
tre can perform this work quickly and efficiently.)
• See respective spare parts list for wear parts.
Change of tools / abrasives: General
• Unplug power supply before each tool change.
• Clean clamp fitting before mounting.
• Ensure flawless runout and only use low-vibration tools. It is es-
sential that you take note of the permissible speed in this context.
4.1 TALM - Angle grinding head with water feed
Attention: Electric current protection
If hand tools with central waterfeed are used one must install a ISK10 -in-
sulater coupling between flex. Shaft and motor mount A2. The electric
unit can only be operated in a low voltage -42V- mode, with a cut-out-
transformer.
Gear transmission ratio approx.
Gear transmission ratio approx.
Tool connection G28
Permissible operating speed up to
Max. tool up to (cup wheels)
accessory) (Fig. C)
C5 Driving pin
Service Cen-
(Fig. E)
Typ 1:1 - i = 1:1
Typ 2:1 - i = 2:1
ø 28 mm
9'600 min
-1
ø 150 mm (max. 1'700 RPM)
Max. tool up to (cup wheels)
Spindle (see spare parts list)
Weight
For shaft type NA 12
Machine elements
1 Water hose barb
2 Water tap
3 Wrench 14 mm
4 Handle
Suitable tools
9 Cup grinding wheels for ferrous -non ferrous material; for stone and
marbel with or without water.
Change of tools/abrasives (from the spindle)
Hold on to spindle 6 with key 5
Mount or dosmount adapter 8 with key 7. Change of tools (cup
grinding wheel 9 from adapter 8)
Mount or dismount cup grinding wheel 9 by hand (quick change
coupling).
4.2 TAM - Angle grinding head with water feed
Attention: Electric current protection
If hand tools with central waterfeed are used one must install a ISK15 -in-
sulater coupling between flex. Shaft and motor mount A2. The electric
unit can only be operated in a low voltage -42V- mode, with a cut-out-
transformer.
Gear transmission ratio approx.
Gear transmission ratio approx.
Tool connection G35
Permissible operating speed up to
Max. tool up to (cup wheels)
Max. tool up to (cup wheels )
Spindle (see spare parts list)
Weight
For shaft type NA 15
Machine elements
1 Water hose barb
2 Water tap
3 Wrench 14 mm
4 Handle
Suitable Tools
9 Cup grinding wheels for ferrous -non ferrous material; for stone and
marbel with or without water.
Change of tools/abrasives (from the spindle)
Hold on to spindle 6 with key 5
• Release or tighten adapter 8 with key 7. Change of tools (cup
grinding wheel 9 from adapter 8)
• Release or tighten cup grinding wheel 9 by hand (quick change
coupling).
4.3 FSM - Right angle grinde
Gear transmission ratio approx.
Gear transmission ratio approx.
Tool connection G28
Permissible operating speed up to
Max. tool up to
Spindle (see spare partslist)
Weight
For shaft type NA 12
Machine elements
1 Allen wrench
4 Side handle
2 Screw
5 Wrench 17 mm
3 Handle mount
6 Spindle
Change of side handle (left to right)
Release and then firmly tighten threaded element 2 of handle mount 3
with allen wrench 1.
ø 120 mm (max. 2'800 RPM)
M14 (5/8"-11)
1,3 kg
DIN 10 / G28
5 Wrench 17 mm
6 Spindle
7 Wrench 27 mm
8 Quick change flange
(Fig. F)
Type 1:1 - i = 1:1
Type 2:1 - i = 2:1
ø 35 mm
6'400 RPM
ø150 mm (1'700 RPM)
ø120 mm (2'800 RPM)
M14 or 5/8"-11
2.6 kg
DIN 15 / G35
5 Wrench 17 mm
6 Spindle
7 Wrench 27 mm
8 Quick change flange
(Fig. G)
Type 1:1 - i = 1:1
Type 2:1 - i = 2:1
ø 28 mm
12'000 RPM
ø 180 mm
M14 or 5/8"-11
1.3 kg
DIN 10 / G28
7 Wrench
8 Directly-mounted tools
5

Publicidad

Tabla de contenido
loading

Tabla de contenido