Remote Control - Steren CCTV-965 Guía Rápida

Before using this 4 channel digital video recorder, read this
instruction manual in order to avoid any malfunctions. Save this
instruction manual for future reference.
IMPORTANT
• This device should be placed in an area with adequate
• ventilation.
• Do not expose this device to direct sunlight, dust, or humidity.
• Always use a soft and dry cloth in order to clean this device.
• If the power cord is damaged it must be replaced immediately by
the manufacturer, your service agent, or any qualifies personnel.
CONTROLS
FRONT PANEL
1.- RSVD-LED
indicator: light on
3
when the DVR
works well.
2
2.- Rec
1
indicator:
light on when
24
start to recording.
3.- Power indicator:
light on when the
device is in use
4.- CH 1: Allows you to select the camera connected to channel 1
5.- CH 2: Allows you to select the camera connected to channel 2
6.- CH 3: Allows you to select the camera connected to channel 3
7.- CH 4: Allows you to select the camera connected to channel 4
8.- All: Allows you to view all four cameras at the same time on one
screen.
9.- Up: Allows you to move through the menu options up
10.- Select: Allows you to confirm or change a selection
11.- Left: Allows you to move through the menu options left
12.- Power: turn on or turn off the device.
13.- Rigth: Allows you to move through the menu options right
14.- IR sensor: Receives the infrared signal from the remote control.
15.- Down: Allows you to move through the menu options down
16.- Stop: In playback mode, allows you to stop the current playback.
In recording mode, stops the current recording.
17.- Menú: Accesses the main menu
18.- FF: In playback mode, allows you to skip forward to a specific
point in the video. Press again this button and the speed from forward
will be 1x to 6x
19.- Rec: Begins recording.
20.- Pause: In playback mode, allows you to pause a video being
played.
21.- AUD-SEL: to change the audio output from channel 1 or 2
22.- Play: Begins / restarts the playback of a saved file.
23.- Mute: mute audio out sound.
24.- Rew: In playback mode, allows you to return to a specific point of
the video. Press again this button and the speed from return will be 1x
to 6x
REAR
PANEL
2
1
14
ENGLISH-01
4 5 6 7
8 9 10 11
13
18 16 15 14
22 20
23 210 19
17
3 5
4
6 7
11 9
13 10
12
1 y 2.- Video output.
Allow you to connect a monitor through a BCN connector.
3.- Main out VGA: Allow you to connect a monitor through a VGA
connector.
4.- Audio in CH2: audio input
5.- CH1: Allows you to view the camera 1
6.- CH3: Allows you to view the camera 3
7.- USB port: you can backup with a USB device or can to connect a
USB mouse and to move in the main menu.
8.- Power input
9.- RS485 port: to connect a PTZ devices with protocols PELCO-D/
PELCO-P
Sensor: to connect four motions sensors.
Alarm: to connect a alarm system.
10.- CH4: Allows you to view the camera 4
11.- CH2: Allows you to view the camera 2
12.- Audio in CH1: audio input
13.- Audio out: connect DVR to audio in on your monitor or TV so you
can hear recorded sound from TV speakers.
14.- Network port.

REMOTE CONTROL

1.- Record: Begins recording.
2.- Enters or exits the main menu
and when is in playback enters the
menu from playback.
3.- This button to change audio
12
output Channel 1 or channel 2.
4.- Rew: In playback mode, allows
you to return to a specific point
from the video.
Press again this button and the
speed from return will be 1x to 6x
5.- Numbers keys: Press 1 and you
will see in screen the camera 1,
press 2 and you will see the camerà 2, etc. also this keys can add
numbers in IP configs.
6.- Mute: Mute audio out sound.
7.- Play: Begins / restarts the playback of a saved file.
8.- Pause: In playback mode, allows you to pause a video being
played.
9.- Forward: In playback mode, allows you to skip forward to a speci-
fic point in the video.
Press again this button and the speed from forward will be 1x to 6x
10.- Quad: Allows you to view all 4 cameras on the same screen at
the same time.
11.- Select: Allows you to confirm or change a selection
12.- Up/Down/Right/Left Keys: to move in the main menu.
13.- Stop: Stops current playback or current recording.
HARD DRIVE INSTALLATION (not
Make sure taht you have to kown the computers. if not go with a
qualified person.
1. Remove the seven screws from the devices cover and pull the
cover out.
2. Connect the SATA cable to your hard drive.
3. Connect the power cable to the hard drive
4. Place the hard drive in the interior of the video recorder. In order
to set it in place, screw in each side of the hard drive.
8
12
13
1
2
3
4
5
included)
ENGLISH-02
11
10
9
8
7
6