Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
PFS AA-652
For Installations Using Co-Extruded Composite, Classic and Estate Balusters
For each 6' on-center railing section you will need:
One 6' Deckorators CXT Line or Stair Rail Kit, which contains:
* (1) Upper rail
* (1) Lower rail
* (2) Inner rails
* (2) Support block kits
• (2) 4" Support blocks
• (2) Support block connectors with screws
* (1) In-line or stair hardware kit, which contains:
• (4) In-line or stair brackets
• (16)1" long countersunk screws
• (4) 1-1/2" long pan head screws
• (8) 2" long countersunk screws
• (2) 2-1/2" long countersunk screws
• (1) Drill bit
• (1) Screw pack consisting of 30 screws
(use with Deckorators Baluster Connectors)
• (1) Post Sleeve Bracket placement template
Baluster options:
One Co-Extruded Composite Baluster Kit,
which contains:
* (15) – Balusters
* (30) – Baluster Connectors with screws
One and a half Classic or Estate Aluminum Baluster Kits,
which contain:
* (10) – Aluminum Balusters
and
One and a half Classic or Estate Baluster Connector Kits,
which contain:
* (20) – Baluster Connectors
* (20) – Stair Adaptors if applicable
Two Scenic Glass Baluster Kits, which contain:
* (5) – Glass Balusters
and
Ten Scenic Baluster Connector Kits, which contain:
* (2) – Glass Baluster Connectors
* (2) – Glass Baluster Stair Connectors if applicable
One 40" or 52" Post Sleeve Kit, which contains:
* (1) – post sleeve
* (1) – post base trim
One Post Cap for each post sleeve (Sold separately)
Each Deckorators CXT Rail Kit includes:
(1) - Upper rail (Colonial or Contemporary Style)
(1) - Lower rail
(2) - 4" Support blocks
LowerRail.ai
SupportBlock.ai
2
6' Rail Installation Instructions
or
(2) - Inner rails
ColonialRail.ai
ContemporaryRail.ai
(2) - Support block
connectors
with screws
Items you will need:
ConnectorWScrew.ai
• Construction adhesive
• Drill/power screwdriver
• Marked speed square
• Assorted drill bits
• Two clamps
• Hammer
• Carpenter's level
• Miter or circular saw with
• Carpenter's pencil
fine-tooth carbide tip blade
RailRetainer.ai
Prior to construction, check with your local regulatory agency for special
code requirements in your area. Common railing heights are 36" and
42". Structural support should come from the continuation of deck
support posts that extend up through the deck floor or from railing
posts that are bolted to the inside of the rim or outer joists. Never
span more than 6' on-center between railing posts. Install railing posts
before deck boards are fastened to the joists.
Pre-drilling of all railing components is essential to successful
installation. Do not over-tighten screws. Read instructions completely
to get an understanding of how the product goes together and how each
piece affects the other.
Step 1: Determine the number
of railing posts needed for your
deck. Post spacing is 6' on-
center. Example: A 12'x16' deck
attached to a building with a
4' access opening on one side
will require a total of eight posts
(fig. 1).
Deckorators
(1) - Drill bit
(4) - In-line or stair brackets
CXTBracket.ai
(16) - 1" long
(4) - 1-1/2" long
countersunk screws
pan head screws
Bit.ai
(8) - 2" long
(2) - 2-1/2" long
countersunk screws
countersunk screws
• Adjustable wrench or socket
wrench for bolts, etc.
• Safety glasses/goggles
• Assorted fasteners
(see instructions)
• Tape measure
fig. 1
PAGE 1 - 6' CXT Rail_ENG
CXT
®
6475_8/11
Publicidad
Manuales relacionados para DECKORATORS CXT
Resumen de contenidos para DECKORATORS CXT
- Página 1 For Installations Using Co-Extruded Composite, Classic and Estate Balusters For each 6' on-center railing section you will need: Each Deckorators CXT Rail Kit includes: One 6' Deckorators CXT Line or Stair Rail Kit, which contains: * (1) Upper rail * (1) Lower rail...
- Página 2 Remove an additional 1/16" from the Deckorators connectors are too long for use with the CXT railing system. the pencil mark on each end and trim the inner rail to length. Repeat for the second inner rail (fig.
- Página 3 1/8" shorter than the lower rails with all holes equally spaced. Remove an additional 1/16" from the pencil mark on each end and trim fig. 7 the inner rail to length. Repeat for the second inner rail (fig. 7). PAGE 3 - 6' CXT Rail_ENG...
- Página 4 Deckorators railing is a decorative railing and can only be used in those applications where a structural railing is not required by building codes. Deckorators is not suitable for structural use. It should not be used for primary load-bearing members such as posts, joists, beams or stringers. The same common-sense precautions should be taken when handling Deckorators as with wood or other building materials.
- Página 5 Pour chaque section de traverse centre-à-centre de 6 pi, Chaque trousse de traverses Deckorators CXT inclut : vous aurez besoin de ce qui suit : Une trousse de traverses d'escalier ou en ligne Deckorators CXT de 6 pi qui contient : * (1) traverse supérieure * (1) traverse inférieure...
- Página 6 30 vis de 1 po inclus dans la trousse de extérieures avec tous les trous espacés de manière égale. Retirez un autre traverse. Les vis incluses avec les raccords Deckorators sont trop longues 1/16 po de la marque de crayon à chaque extrémité et taillez la traverse pour les utiliser avec le système de traverse CXT.
- Página 7 Tapez doucement sur les balustres avec un maillet en caoutchouc afin d’éliminer tout espacement possible. Nivelez d’un bout à l’autre. Étape 12 : Important : en utilisant les raccords de balustre Deckorators Designer fig. 6 (Estate et Classic), la traverse intérieure supérieure doit être inversée (fig.
- Página 8 La traverse Deckorators est une traverse décorative et peut être utilisée seulement dans les applications où une traverse structurale n'est pas requise par les codes de construction. Les mêmes précautions que l’on prend avec le bois ou d’autres matériaux de construction devraient être prises lors de la manipulation de produits Deckorators. Des masques protecteurs contre la poussière et du matériel qui protège les yeux sont recommandés afin d’éviter les irritations produites par les copeaux et les sciures de bois.
- Página 9 Para cada sección de barandal de 6 pies de centro a Cada kit de barandal Deckorators CXT incluye: centro necesitará: Un kit de barandal en línea Deckorators CXT o kit de barandal para escaleras, de 6 pies, que contiene: * (1) Barandal superior...
- Página 10 Si está utilizando balaustres de aluminio interiores deberán ser 1/8" más cortos que los barandales exteriores con todos Deckorators con los conectores, utilice el paquete de 30 tornillos de 1" que se los orificios espaciados de la misma forma. Quite 1/16" adicional de la marca incluyen en el kit del barandal.
- Página 11 Paso 12: Importante: al utilizar los conectores para balaustres Deckorators Designer (tanto Estate como Classic), debe invertirse el barandal superior interior (figura 5). Use un adhesivo para exteriores en el lado inferior de los conectores para balaustres Designer para evitar que los balaustres giren.
- Página 12 Repita en el poste adyacente. Coloque el barandal interior entre El barandal Deckorators es un barandal decorativo y sólo puede utilizarse en aquellas aplicaciones en las que los códigos de construcción no requieran un barandal estructural. Deckorators no es adecuado para uso estructural.