DECKORATORS CXT Instrucciones De Instalación página 4

Stair Railing Installation Instructions
fig. 8
Step 6: Assemble the lower inner rail and support block assembly. Position
the bottom rail between the posts. Check building code requirements
for maximum spacing on a staircase, typically less than 6". A 6" ball
cannot pass through the triangle formed by the bottom rail, tread and
riser. (See fig. 8.) A support block is needed every 2' on-center. Trim
support blocks to desired height and pre-drill 1/8" holes in the proper
location. Holes must be centered on the inner rail for support blocks to
fit properly. Using the support block connectors, fasten support blocks
to the underside of the inner rail.
Step 7: Mark the height of the brackets on the inside of the post using the
bracket placement template included in the kit. Another option is to use
the inner rail as a guide. The top of the bracket should be even with the
top of the inner rail assembly. Drill two 1/8" holes through the bracket
holes shown on the template and through the post sleeve, for both the
upper and lower brackets. Remove the bracket placement template from
the post sleeve and fasten the upper and lower brackets to the post using
two 2" long countersunk screws. Tip: For best results, use a long drill bit
or add an extension bit to the drill. Repeat on the adjacent post. Set the
inner rail in place and pre-drill eight 1/8" holes at each bracket hole
and into the inner rail. Fasten the rail to the bracket using eight 1" long
countersunk screws.
Deckorators railing is a decorative railing and can only be used in those applications where a structural railing is not required by building codes. Deckorators is not suitable for structural use. It should
not be used for primary load-bearing members such as posts, joists, beams or stringers. The same common-sense precautions should be taken when handling Deckorators as with wood or other
building materials. Dust masks and eye protection devices are recommended to avoid possible irritation from sawdust and chips. Gloves will help to protect the hands. Hands should be washed after
doing construction work.
The diagrams and instructions in this brochure are for illustration purposes only and are not meant to replace a licensed professional. Any construction or use of the product must be in accordance with
all local zoning and/or building codes. The consumer assumes all risks and liability associated with the construction or use of this product. The consumer or contractor should take all necessary steps
to ensure the safety of everyone involved in the project, including, but not limited to, wearing the appropriate safety equipment. EXCEPT AS CONTAINED IN THE WRITTEN LIMITED WARRANTY, WARRANTOR
DOES NOT PROVIDE ANY OTHER WARRANTY, EITHER EXPRESS OR IMPLIED, AND SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING CONSEQUENTIAL DAMAGES.
Manufactured by UFP Ventures II, Inc., a Universal Forest Products Company, 801 E. Lessard, Prairie du Chien, WI 53821
©2011 Universal Forest Products, Inc. All rights reserved. Deckorators is a registered trademark of Universal Consumer Products, Inc. in the U.S. and other countries.
continued
ASTM D 7032 compliant. See CCRR-0171 at www.ati-es.com for uses and performance levels. 6475_7/11
Step 8: Set the lower rail on the lower inner rail between the posts. Using
two 2-1/2" long countersunk screws, set the two outermost connectors. For
co-ex composite balusters, use the connectors that come with the baluster
kit. For Deckorators aluminum or glass balusters, use the appropriate
stair adaptor (sold separately) with the proper baluster connector (sold
separately). Using the screws provided with the baluster connectors,
install the balance of the baluster connectors onto the lower rail assembly.
Step 9: Determine the length of the balusters. Fig. 3 illustrates how a 36"
high railing might be sized. Use fig. 3 as a planning tool to determine
the height to cut the post sleeves and the balusters. Note: Use a fixture
to ensure a consistent length (+/- 1/16"). If using co-ex composite
balusters, the baluster will need to be miter cut to the proper stair angle.
Trim the balusters to the required angle (co-ex composite balusters
only) and length. (One per hole in lower rail). Install balusters on each
connector. Gently tap the balusters with a rubber mallet to eliminate any
gaps. Check for level end to end. Tip: Wrap painters tape around the back
side of both posts and place balusters against the tape. The tape will balance
the balusters in place until the upper rails are installed. Remove tape when
upper rail is in place.
Step 10: Important: when using Deckorators Designer Baluster Connectors
(both Estate and Classic) in conjunction with the stair adaptors, the upper inner
rail must be inverted (fig. 5). Use an exterior adhesive on the underside of the
Designer Baluster Connectors to prevent the balusters from spinning. Install
the remaining baluster connectors and stair adaptors (if applicable) on the
underside of the upper inner rail. Set the rail onto the balusters, gently
tapping the rail to remove any gaps. Attach the inner rail to the brackets
by pre-drilling eight 1/8" holes at each bracket hole and into the inner rail.
Fasten the rail to the bracket using eight 1" countersunk screws.
Step 11: Measure the distance between the posts and trim the upper outer
rail to length, and set on the assembly. Taking care not to drill all the way
through the upper rail, use a 1/8" drill bit to pre-drill four 1/2" deep holes,
equally spaced, through the underside of the inner rail and into the underside of
the upper rail. Tip: Place a piece of tape 1-1/2" from the end of the drill bit. Do
not drill past the tape. Fasten cap rail in place using four 1-1/2" pan head
screws.
Step 12: Apply construction adhesive to the inside edges of the post caps
and place over each post sleeve.
Note: Touch-up paint is available to repair any chips or blemishes that occur
during assembly and installation. Contact a Deckorators customer service
agent at 800-332-5724 for availability.
877.463.8379 www.deckorators.com
PAGE 4 - 6' CXT Rail_ENG