Westin 32-1480 Instrucciones

AUTOMOTIVE PRODUCTS, INC.
BULL BAR ASSEMBLY
ENSAMBLE DE PARRILLA
DELANTERA CON TIRÓN
LA BULL BAR
32-1480
32-1485
ITEM QTY
1 1 BULL BAR ASSEMBLY
2 2 PLASTIC PLUG
3 4 RUBBER BUMPER
4 2 M12-1.25 X 60MM HEX HEAD BOLT
5 2 M12-1.25 X 30MM HEX HEAD BOLT
6 4 1/2" FLA T WASHER
7 4 1/2" LOCK WASHER
8 2 SPACER TUBE
1 1 ENSAMBLE DE PARRILLA DELANTERA CON TIRÓN
2 2 TAPONES DE PLÁSTICO
3 4 PARACHOQUES DE HULE
4 2 PERNOS CON CABEZA HEXAGONAL DE M12-1,25 X 60MM
5 2 PERNOS CON CABEZA HEXAGONAL DE M12-1,25 X 30MM
6 4 ARANDELAS PLANAS DE 1/2"
7 4 ARANDELAS DE PRESIÓN DE 1/2"
8 2 TUBO SEPARADOR
1 1 LA BULL BAR
2 2 BOUCHONS DE PLASTIQUE
3 4 PARE-CHOCS CAOUTCHOUC
4 2 BOULONS À TÊTE HEXAGONALE M12-1,25 X 60MM
5 2 BOULONS À TÊTE HEXAGONALE M12-1,25 X 30MM
6 4 RONDELLES PLATES 1/2 PO
7 4 RONDELLES À FREIN 1/2 PO
8 2 TUBE D'ESPACEMENT
STEP 1.
Remove the contents from box and check for damage. Verify all parts are present. Read instructions completely
before beginning.
STEP 2. NOTE:
Bull Bar will obstruct front license plate. If local/state laws prohibit this, license plate relocation kit 32-0055
may be purchased separately.
VEHICLES WITH TOW HOOKS AND FACTORY SKID PLATE
STEP 3.
If vehicle is equipped with tow hooks, factory skid plate, or both, they must be removed to complete installation.
SEE ALSO STEP 2.
STEP 4.
Slide Bull Bar Assembly through tow hook openings and attach as shown.
STEP 5.
Level and adjust Bull Bar as desired and tighten all fasteners. Recommended torque value is 79 Ft. Lbs. for 12mm
fasteners.
LIGHT INSTALLATION:
Insert threaded stud on base of the light through hole in cross tube. Using a ratchet, extension and socket
for correct size of nut supplied, insert through large clearance hole in bottom of cross tube. Thread nut and
washers on stud and tighten.
started.
NOTE:
Fits most 6" round or rectangle lights. Some lights may require replacing included mount/isolator with rubber
FINISH PROTECTION
Westin products have a high quality finish that must be cared for like any other exposed finish on the vehicle. Protect the finish with a non-abrasive automotive wax, (e.g. Pure Carnauba)
on a regular basis. The use of any soap, polish or wax that contains an abrasive is detrimental, as the compounds scratch the finish and open it to corrosion.
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION:2004-08 NISSAN TITAN PICK-UP KING CAB AND CREW CAB 2/4 WHEEL DRIVE
2004-0 NISSAN ARMADA SUV 2/4 WHEEL DRIVE
APLICACIÓN: PICK-UP NISSAN TITAN KING CAB Y DOBLE CABINA, TRACCIÓN 2/4, MOD. 2004-08
NISSAN ARMADA SUV, TRACCIÓN 2/4, MOD. 2004-08
APPLICATION: CAMIONNETTE NISSAN TITAN CABINE ALLONGEE ET CABINE DOUBLE A 2 OU 4 ROUES
MOTRICES 2004-08
VEHICULE UTILITAIRE SPORT NISSAN ARMADA A 2 OU 4 ROUES MOTRICES 2004-08
1
CONTENTS - CONTENIDO
SEE FIGURE 1. NOTE:
- CONTENU
A short socket, not a deep well works best to get the nut
8
TOOLS - HERRAMIENTA
19MM WRENCH
19MM SOCKET
17MM WRENCH
17MM SOCKET
RATCHET
TORQUE WRENCH
DADO DE 19MM
LLAVE DE TUERCAS DE 19MM
DADO DE 17MM
LLAVE DE TUERCAS DE 17MM
MANERAL
LLAVE DE TORQUE
DOUILLE 19MM
CLE 19MM
DOUILLE 17MM
CLE 17MM
CLIQUET
CLE DE COUPLE
SEE FIGURE 2.
WO: 75-0416 REVISION B 3/20/08
- OUTILS