Parts And Components; Product Assembly; Before Use - cecotec CONGA ROCKSTAR 900 ULTIMATE ERGOFLEX Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 14
ENGLISH

1. PARTS AND COMPONENTS

Fig. 1
0.
Suction base
1.
Floor brush release button
2.
Vacuuming tube release button
3.
Dust tank bottom cover unlock button
4.
Dust tank emptying button
5.
Speed-control dial
6.
Display
7.
On/off button
8.
Power adapter
9.
Fast charge base
10. Includes a 2-in-1 narrow accessory for corners and furniture
11.
Includes a wide 2-in-1 accessory for corners and furniture
12.
Motorised brush for upholstery.
13.
Union elbow
14. Long brush
15.
Flexible hose
16.
Flex vacuuming tube
17.
Jalisco brush
18. Best Friend Care special brush for pet hair
19.
Special brush for fabrics
Fig. 1.1
1.
Display
2.
Speed-control dial
3.
On/off push button

2. BEFORE USE

Take the product out of the box.
Check for any visible damage. If any is observed, contact as soon as possible the Technical
Support Service of Cecotec for advice or reparation.
Fully charge the device before the first use.
During the first 3 uses, it is recommended to charge the device for 12 hours between uses. Once
the battery has been charged and used, it will start charging normally.
The normal charge time is 2 hours approx. When the battery is fully charged, unplug it.
32
CONGA ROCKSTAR 900 ULTIMATE ERGOFLEX

3. PRODUCT ASSEMBLY

Vacuuming tube and suction base assembly
To install the suction base into the vacuuming tube, align both of them making sure the tab on
the suction base matches the guides on the tube, and introduce one into the other until they
are firmly fixed. To disassemble them, press the suction base release button and pull from the
vacuuming tube while you hold the suction base.
Warning: When assembling these 2 parts, make sure the handle and the brush are facing the
same direction.
Use the Flex tube to reach and vacuum dirt from the most inaccessible zones. Press the Flex
button to bend the tube.
Fig. 2.1/2.2
Battery assembly
Introduce the battery in the slot located in the handheld vacuum cleaner. Once it is introduced,
it will click into place. Move it slightly to ensure it is properly assembled in place.
Note: Take the battery out and store it in a safe, dry place if the device is not going to be used
in a long period of time.
Fig. 3
Following the below illustration, keep the vacuuming tube vertically, align the tab on the
vacuuming tube with the guides in the handheld vacuum cleaner and introduce the tube.
Dust tank and handheld vacuum cleaner assembly
To assemble the dust tank to the handheld vacuum cleaner, first separate the handheld
vacuum cleaner from the vacuuming tube.
Then, press the vacuuming tube release button with one hand and, holding from the handle
with the other one, turn the dust tank anticlockwise to the unlock position indicated on the
dust tank edge.
Fig. 4
4. OPERATION
Wall charging base installation
First, fix the charging base to the wall. To do so, we recommend you place a protective film
(not included) on the wall's surface. Then, put the charging base on the wall and make 3
corresponding to the holes to be drilled in order to fix the base. Take into account the height of
the installation, it is important that suction base rests on the floor to avoid the charging base
from holding all the vacuum cleaner's weight. Make 3 holes on the wall and fix the charging
base with the supplied M4 x 32 nuts and screws.
ENGLISH
CONGA ROCKSTAR 900 ULTIMATE ERGOFLEX
33

Hide quick links:

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Conga rockstar 900 ultimate ergoflex05707

Tabla de contenido