Initial Snow Thrower Setup; Tools Required; List Of Loose Parts; Assembly - Honda HS750EA El Manual Del Propietario

INITIAL SNOW THROWER
SETUP

Tools Required

10 mm wrench and a 12 mm wrench

List of Loose Parts

With help from an assistant, carefully remove the snow thrower and
loose parts from the carton and compare the loose parts against the
following list. Contact the authorized Honda dealer from whom you
purchased the snow thrower if any of the loose parts shown are not
included with your snow thrower.
Ref.
No.

Chute guide and handle (EMA type only)

6 mm chute setting bolt (EMA type only)

6 mm self-locking nut (EMA type only)

Owner's Manual


Assembly

1. Loosen the two 8 mm flange nuts [1].
(EA type shown)
4
Description
  
QUICK FIND
Auger ..................................................... 12 Fuel System Maintenance......................
Contact Honda ....................................... 20 Maintenance Schedule...........................
Find a Dealer ......................................... 20 Oil Change .............................................
Fuel .......................................................... 6 Oil Level Check ........................................
CONTENTS
FOR YOUR SAFETY .............................. 2 Spark Plug.........................................
PARTS AND CONTROLS ...................... 3 Auger.................................................
INITIAL SNOWTHROWER SETUP ........ 3 TRANSPORTING .................................
Assembly............................................. 4 STORAGE
BEFORE EACH OPERATION Fuel ...................................................
Check Your Snowthrower.................... 5 Oil ......................................................
Check Your Working Area................... 5 Cleaning ............................................
Check the Oil Level ............................. 5 Storage Location ...............................
Add Fuel .............................................. 6 Removing From Storage ...................
OPERATION
TROUBLESHOOTING
Operating the Controls ........................ 7
Electric Starter Will Not Operate (AS type)
Starting the Engine.............................. 9 15
Stopping the Engine .......................... 10 Starter Operates But Engine Will Not Start
(AS type) ...........................................
SERVICING YOUR SNOWTHROWER
Engine Runs, But Snowthrower Does Not
Maintenance Safety........................... 10
Operate .............................................
Maintenance Schedule...................... 11
Engine Has Low Power .....................
Oil Change ........................................ 11
Snow Not Discharging Properly ........
For more information about your
snowthrower, visit
www.powerequipment.honda.com
and click on FAQs or scan the QR
code shown here.
© 2013 American Honda Motor Co., Inc. www.powerequipment.honda.com
All Rights Reserved
2. Raise the handlebar into position, and then tighten the two 8 mm
flange nuts securely. During initial setup, tighten the two
handlebar attaching 8 mm flange nuts to 5.9 N•m using a torque
wrench. This torque is achieved by tightening the flange nuts
approximately 1/4 turn after the bolt free-play is eliminated. Do
not over-tighten the nuts. Over-tightening these nuts will cause
excessive vibration to be transferred to the upper handlebar.
TORQUE: 5.9 N•m
3. EMA type only: Install the discharge chute using the three 6 mm
chute setting bolts [1] and 6 mm self-locking nuts [2]. Make sure
the bolt head goes on the inside and the nuts on the outside.
Tighten the nuts to the specified torque:
TORQUE: 10 N•m
(EMA type only)
Qty.
1
3
3
1
[1]
OWNER'S MANUAL
HS720A • HS720AS
HS720AM
(inside chute)
SNOWTHROWER
Before operating the snowthrower for the first time, please read this
Owner's Manual. Even if you have operated other snowthrowers,
take time to become familiar with how this snowthrower works and
practice in a safe area until you build up your skills.
19 Scraper blade .........................................13
11 Spark Plug ..............................................12
11 Warranty Coverage.................................21
5
12 Engine Stalls When the Auger Clutch Lever
12 is Engaged ........................................... 16
TECHNICAL INFORMATION
14
Serial Number Locations ...................... 16
High Altitude Operation ........................ 16
14
Emission Control System ..................... 17
14
Air Index ............................................... 17
15
Specifications ....................................... 18
15
15 FUEL SYSTEM MAINTENANCE............. 19
CUSTOMER INFORMATION
Parts, Accessories, and Service Items. 20
Dealer Locator Information................... 20
How to Contact Honda ......................... 20
15 Honda Publications .............................. 20
DISTRIBUTOR'S LIMITED WARRANTY. 21
15
EMISSION SYSTEM WARRANTY .......... 22
16
PRODUCT REGISTRATION ................... 23
16
Contact your Honda dealer.
There is a dealer locator at
4. Lift the spark plug door
and attach the spark plug
cap to the spark plug.
[1]
5. Remove any packing
material from the handlebar and side of the
snow thrower.
ENGLISH
[2]
(outside
chute)