JANE nurse cruiser Manual Del Usuario página 20

GB
cruiser
1.7 Removing 5-Point Harness and Storage the Accessory Part
Step 1: Removing Shoulder Pads and Belts
Loosen the 5-point harness of the child seat as much as possible. Remove the belt from the metal link.
Remove the shoulder pad from the seat belt and keep it in a safe place.
Storage metal link to metal link area on the behind of the backrest. (Picture A and Picture B)
Take the METAL PLATE out of the plastic part and store it in the place designed for this on the back of
the backrest. (Picture C)
Finally put redundant belt into cloth cover. (Picture D)
Step 2: Storage Buckle
Open the buckle, take out buckle tongues from shoulder belt. Pull down buckle cross cloth cover.
Later pick up the cover in the PE board and storage the buckle. (Picture E and F)
1.8 Removing Sleeping Pads
When your child's height exceed 61cm, remove the sleeping pads.
1.9 Removing and Putting on the Fabric Cover
1. Remove the 5-point harness.
2. Take off the cover from the backrest and base.
3. Move the headrest of the child seat up to the highest position.
4. First take the cover off base of the headrest, then remove the cover of the headrest.
To re-fit the cover, Firstly put on the headrest's cover, then put on the plastic shell's cover in the order of
(see picture 1).
CAUTION! Never use the child seat without a correctly installed.
CAUTION! Check that the harness straps are not twisted and that they have been correctly inserted in
the belt slots of the cover.
2 2.INSTALLATION
2.1 Installed in Rearward Facing Position with ISOFIX and top tether (40-105cm)
Put the ISOFIX insert guide into the two ISOFIX attachment points of your vehicle.
If you don't have ISOFIX insert guide, please Ignore this step.
NOTE: The ISOFIX attachment points are located between the surface and the backrest of the vehicle
seat.
Press the ISOFIX button to pull out the two locking arms from the base bottom. Pull the locking arm to
and fro until you hear an audible CLICK which indicates they are fully engaged. And on both sides of the
locking arms button turn into green safety color.
Pull out the top tether,and press the release button, pull the top tether long enough to hang the latch
on the back of the car seat.
Fix the latch on the fixed point,and the position of the fixed point are shown in the picture (one of the three
positions). Make sure the top tether clip is tightened up.
NOTE: For the safety of your child, the top tether must be tightened up during driving.
2.2 Installed in Forward Facing Position with ISOFIX and top tether (76-105cm)
IMPORTANT: Do not use forward facing before the child's age exceeds 15 months.
Put the ISOFIX insert guide into the two ISOFIX attachment points of your vehicle.
If you don't have ISOFIX insert guide, please ignore this step.
NOTE: The ISOFIX attachment points are located between the surface and the backrest of the vehicle
seat.
Press the ISOFIX button to pull out the two locking arms from the base bottom. Pull the locking arm
to and fro until you hear an audible CLICK which indicates they are fully engaged. And on both sides of
the locking arm's button turn into green satety color.
Pull out the top tether and press the release button, pull the top tether long enough to hang the latch
on the back of the car seat.
Fix the latch on the fixed point, and the position of the fixed point are shown in the picture (one of the
three positions). Make sure the top tether clip is tightened up.
NOTE: For the safety of your child, the top tether must be tightened up during driving.
2.3 Installed with ISOFIX connector and Belt or only Adult seat belt (100-135cm)
NOTE When you use this safety car seat in 100-135cm, please remove the 5-point harness, refer to Chapter 1.7.
Place the child seat forward facing on the vehicle seat (in the direction of travel).
20
Put the ISOFIX insert guide into the two ISOFIX attachment points of your vehicle.