DynaTrap DT1050 Manual Del Propietário

DT1050
OWNER'S MANUAL
Thank you for purchasing
the DYNATRAP Insect Trap!
®
This product may be covered by one or more U.S. patents
or pending patent applications. See www.DynaTrap.com/patents
IMPORTANT: READ CAREFULLY
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS
WARNING:
when using electric appliances, basic precautions should
always be followed, including the following:
1. Please read all instructions before using the DynaTrap Insect Trap and keep for future reference.
®
2. To disconnect, twist housing to the 'OFF' position, then remove plug from outlet.
3. To reduce the risk of injury from moving parts or electric shock, always turn unit off and disconnect plug when
not in use and before servicing or cleaning.
4. Always unplug before replacing lamp. Replace with same type rated 7-Watt bulbs, DynaTrap
5. Do not position the unit near heat, gas, oil or other flammable materials.
6. Place out of reach from children.
7. To reduce the risk of electrical shock, do not put appliance in water or other liquid.
8. Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has been dropped or
damaged, or if it has been dropped into water or other liquid.
9. Connect only to a circuit that is protected by a ground-fault circuit-interrupter (GFCI).
10. Do not insert fingers or any foreign objects into the unit while it is connected to an electrical outlet.
11. Collected insects within the unit may contribute to fire, so clean insects from the unit frequently.
12. Do not clean this product with water spray. Do not place where it can fall into water, or near flammable materials.
13. Do not touch fan while in motion.
14. Do not abuse cord—never carry or hang unit by cord or yank it to disconnect from receptacle.
Keep cord away from sharp edges.
15. If using outdoors, use only extension cords with a tag stating, "Suitable for Use with Outdoor Appliances."
16. Use only extension cords that have plug and receptacles that match the product plug. Replace or repair damaged cords.
17. Only use attachments recommended or sold by the manufacturer.
18. This appliance is provided with double insulation. Use only identical replacement parts.
See instructions or Servicing of Double-Insulated Appliances.
INSTALLATION & OPERATING INSTRUCTIONS
1. Unpack unit. Save carton for off-season storage (if needed).
2. Hold the Power switch on the side of the revolving rotation door. Twist the unit to the "POWER ON" position. When
you hear a "click," the machine is turned on.
3. For best catch results leave unit on at all times, except when cleaning or servicing.
4. Catch rate activity will be higher at night. For best catch results it is recommended to keep the unit away from
competing light sources.
5. It is recommended to place the unit at least 20 to 40 feet away from where people will be sitting.
6. This unit is all-weather resistant - designed for outdoor use including rainy conditions.
Intended for household and commercial, indoor and outdoor use.
7. To reduce the risk of electric shock, this appliance has a polarized plug (one blade
is wider than the other). This plug will fit in a polarized outlet only one way. If the
plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician to install the proper outlet. Do not change the plug in any way.
8. SERVICING OF DOUBLE-INSULATED APPLIANCES - In a double-insulated appliance,
two systems of insulation are provided instead of grounding. No grounding means
is provided on a double-insulated appliance, nor should a means for grounding
be added to the appliance. Servicing of a double-insulated appliance requires
extreme care and knowledge of the system and should be done only by qualified
service personnel. Replacement parts for a double-insulated appliance must be
identical to those parts in the appliance. The symbol must be identical to those
arts in the appliance. A double-insulated appliance is marked with the words
"DOUBLE INSULATION", "DOUBLE-INSULATED" or the symbol:
CLEANING
Frequent cleaning will prolong the life of the unit, ensure fire
prevention and provide for more efficient operation.
1. Be sure to clean the unit once per week.
2. To clean, hold the switch on the revolving rotation door and
turn it to the "POWER OFF" position. After hearing the "click,"
the machine is turned off. Unplug the unit.
3. For weekly cleaning, twist the cage clockwise and remove any
buildup from the inside of the retaining cage and fan with the
included cleaning brush.
4. For major cleaning, remove the screw securing the fan housing
to the light housing (A), and gently twist to separate. Do not
disconnect wires. Using the cleaning brush, remove dirt and
debris from the fan housing. Once the cleaning process has
been completed, tuck the wires into the channel of the fan
housing (D). Align the screw holes and place the light housing
on top of fan housing. Secure with a click and tighten the screw
to the base of the light housing.
model 41050.
® IMPORTANT: When replacing the retaining cage –
DO NOT press/push against the screen windows.
REPLACING BULB
Replace with DynaTrap ® bulb #41050
(or equivalent G24 Type - 56V/7W bulb)
The lightbulb life expectancy is approximately 3,000 hours (or about
4 months), and should be replaced regularly to ensure optimal UV
effectiveness. Even though the bulb's light may be visible to you, its
ability to attract mosquitoes diminishes over time.
1. Hold the switch on the revolving rotation door and turn it to the
"POWER OFF" position. UNPLUG UNIT, and allow bulb to cool
before replacing.
2. Remove the screw securing the fan housing to the light housing
(A), and gently twist to separate carefully, do not disconnect
wires. Loosen the screw securing the metal bracket
securing the lightbulb (B) and remove the metal bracket.
Cover the bulb with a cloth to protect your finger and hand.
Grasp the bulb (with your hand and fingers protected by the
cloth) and gently pull the bulb from the socket (C).
3. Remove any debris from the lamp socket with cleaning brush.
Insert new bulb. Reposition the metal bracket over the base of
the bulb and tighten the screw. Make sure to tuck the wires into
the channel of the light housing so the wires do not get pinced or
cut by the fan (D). Align the screw holes and
place the light housing on top of fan housing. Secure with a
"click" and tighten the screw to the base of the light housing.
HOW THE DYNATRAP
Flying insects are attracted to the unit by UV light and CO2
that is generated by the photo-catalysis between the UV
lamps and special TiO2 coating. The fan then pulls the insects
into the screened base, trapping them until they dehydrate
and die. The base can be removed, allowing the contents to
be periodically emptied into the trash.
HANGER
TiO
2
ON/OFF SUPERFICIE
COATING
TROUBLESHOOTING
SWITCH CUBIERTA
CON TiO
2
Problem:
Bulb does not
illuminate and fan does
FAN
VENTILADOR
not spin.
UV BULB
RETAINING
CÁMARA
Bulb illuminates, but
CAGE
DE RETENCIÓN
fan does not spin.
Fan spins, but bulb does
not illuminate.
LIMITED WARRANTY
DYNAMIC guarantees to the original purchaser that this product is free from defective materials and workmanship. This warranty
is limited to remedy any defective part for a period of one year from date of original date of purchase. Retain your original
receipt as proof of purchase. This warranty does not apply to the light bulb, nor to, in our judgment, misuse or abuse. If this
unit has been altered, no warranty is in force. This warranty does not apply if this unit is purchased outside the United States,
excluding Canada and Mexico. In no case shall DYNAMIC be liable for any accidental, punitive, consequential, or any other
damages of any kind for breach of this or any other warranty, expressed or implied, whatsoever. Some states do not allow
limitation on how long an implied warranty lasts, so the above limitation or exclusion may not apply to you. This warranty gives
you specific legal rights, and you may also have other rights that vary from state to state.
REPLACEMENT PARTS
HANGER
41050 7-Watt Replacement UV Fluorescent Bulb (1 piece)
To see all replacement and accessory parts available for your DynaTrap, visit www.DynaTrap.com.
TiO
2
ON/OFF
COATING
FOR HOUSEHOLD AND COMMERCIAL, INDOOR AND OUTDOOR USE
SWITCH
Dynamic Solutions Worldwide, LLC
U.S.A. & Canada
12247 W. Fairview Ave. Milwaukee, WI 53226
1-877-403-TRAP (8727)
customercare@dsw-llc.com | www.DynaTrap.com
Mexico
Dynatrap Servicios de Mexico S. de R. L. de C.V.
01-800-880-8727 | servicios@dsw-llc.com
©2019 Dynamic Solutions Worldwide, LLC
HANGER
INSECT TRAP WORKS
®
TiO
2
COATING
FAN
RETAINING
CAGE
FAN
RETAINING
PERCHA CROCHET
CAGE
INTERRUPTOR
Possible cause: Correction:
1. No electrical power. 1. Check plug, receptacle and fuse or circuit breaker.
2. Check to make sure power is switched to the "ON" position.
VENTILATEUR
FOCO UV
1. Shorted fan. 1. UNPLUG UNIT: Examine fan to see that it is free from
CAGE DE
RÉTENTION
foreign material, dirt or buildup of dead insects.
Clean unit as in "CLEANING" section.
1. Bulb not seated properly. 1. Check all sockets for proper bulb seating and alignment.
2. Burnt out bulb. 2. Replace bulb if needed following instructions under
"Replacing Bulb".
TiO
2
COATING
4002907
This device complies with Performance Standards
for Light-Emitting Products, 21 DFR, Part 1040,
Chapter 1, Subchapter J, Radiological health.
HANGER
ON/OFF
SWITCH
ON/OFF
SWITCH
UV BULB
UV BULB
INTERRUPTEUR
AMPOULE
UV
HANGER
ON/OFF
SWITCH