Ecco Blaze II Strobe Instrucciones De Instalacion Y Uso página 2

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Installation & Mounting:
Carefully remove the Minibar and place it on a flat surface. Examine the
unit for transit damage. If damage is found, contact the transit company or
ECCO. Do not use damaged or broken parts.
Permanent Mounting:
Select the mounting location for the Minibar on a flat, smooth surface. If
the Minibar is to be mounted on a curved surface, such as on the roof of
the vehicle, choose a placement with the least amount of curvature. The
mounting location for the Minibar should be chosen such that there is
maximum visibility to the oncoming traffic.
!
Caution!
When drilling into any vehicle surface, make sure that
the area is free from any electrical wires, fuel lines, vehicle upholstery, etc.
that could be damaged.
Use the following instructions for permanent mounting.
1. Using the template on the insert in this manual, mark the locations for
the mounting holes. Use only the original of this template, it is scaled
to show the exact locations for the holes. Use of a copy may result in
the holes slightly off the intended location.
2. Drill the mounting holes using a 7/32" drill.
3. Drill a 3/8" hole for the Minibar's power supply wires. The hole should
be underneath where the Minibar will be mounted. Place the supplied
grommet in the hole, to protect the wires from the sharp edges of the
hole.
4. Place the four (4) mounting bolts in the bottom of the base as shown in
Figure 1. The base has a mechanism to hold the bolts in place for
installation.
5. Mount the Minibar, with the bolts going through the holes drilled in step
2, routing the wire through the grommet installed in step 3. See the
Wiring section of this manual for further wiring instructions. Install
washers and nuts, and secure the unit.
!
WARNING
Failure to follow these instructions can result in fire or injury from excessive heat build up.
Operator is responsible for ensuring cigarette adapter fits correctly into cigarette/auxiliary outlet used.
For proper operation, verify cigarette/auxiliary outlet circuit is rated to supply, a minimum of 10 amps. (See specifications section for rated current in
amperes).
Do not exceed the current rating for the cigarette lighter power outlet recommended by vehicle manufacturer.
Keep cigarette lighter adapter, and outlet, clean and free of debris.
Do not use the cigarette lighter adapter when wet.
Insert cigarette lighter adapter fully into the outlet for proper connection.
Grasp cigarette lighter adapter, NOT cord, to remove from outlet.
Remove cigarette lighter adapter completely from outlet when light is not in use.
920-0011-00 Rev. E
INSERT BOLT
THROUGH LARGE
END OF SLOT
Vacuum-Magnet Mounting:
The vacuum-magnet mount feature includes two (2) suction cups on the
bottom of the Minibar, with a magnet inside each of the suction cups, for
a secure, temporary mount. The Minibar should be placed in the center
of the roof where the least amount of curvature occurs. Before installing,
make sure there is no debris on the bottom of the Minibar or on the roof of
the vehicle, which could reduce the holding power of the suction cups and
magnets. Place and remove the Minibar without sliding to avoid scratch-
ing the paint on the vehicle. After placement, the Minibar should adhere
firmly to the surface. If the unit slides or moves easily, a proper installation
has not been obtained. To release the vacuum, lift each tab to release the
airlock. To protect the rubber cushion/magnet assembly, return bar to the
box when not in use. Do not attempt to attach to ice covered surface.
!
WARNING!
Maximum recommended vehicle speed for safe operation with Vacuum
Mounted bar is 65 mph (104 km/h), when fitted to the center of a vehicle
roof of steel construction.
The vacuum-magnet mount is not intended as a permanent mounting for
the Minibar. The vacuum-magnet mount unit must be mounted on a mag-
netic surface (i.e. no fiberglass, etc.). Insure that the magnet is kept clean.
PUSH BOLT TO
SMALL END
OF SLOT
Figure 1
PULL BOLT
HEAD DOWN
INTO PLACE
Page 2 of 4

Publicidad

Tabla de contenido
loading

Tabla de contenido