DuraMax AD20538G Manual Del Operador página 3

JUMPING START A 12V VEHICLE
A. Turn ignition off before making cable connections.
B. Make sure Power Switch on the front of the unit is on the OFF position until
clamps are connected to the vehicle battery correctly.
C. Connect the red (positive +) clamp to the positive terminal or post on the
vehicle battery.
D. Connect the black (negative –) clamp to a ground away from the battery, such
as an alternator bracket.
E. If connecting the clamps backward, the Connection Status Indicator LED
beside Power Switch will turn Red & flash quickly and an audible alarm will
sound. DO NOT turn the unit on. This could cause serious damage. Reverse
the connections, and the indicator LED will turn Green and the audible alarm
will stop.
NOTE: Your jump starter is used for only 12V vehicles. If connecting to a 24V
vehicle, the Connection Status Indicator LED will turn Red & flash slowly and
an audible alarm will sound. DO NOT turn the unit on. This could cause
serious damage.
F. The Connection Status Indicator LED will turn Green after connection is
correct, and turn Power Switch to the ON position.
G. Start the engine for 3-5 seconds. If the engine does not start within 10
seconds, stop cranking and wait at least 4 minutes before attempting to start t
he vehicle again. This permits the battery to cool down and prevents damage
to the unit and to your vehicle's system from overheating.
H. Turn the unit off and disconnect the clamps, first negative and then positive.
Store clamps properly on the unit.
I. Recharge the unit after use.
USING AS A 12V POWER SOURCE
A. Connect the red (positive +) clamp to the positive input terminal and the black
(negative –) clamp to the negative input terminal.
B. Make sure that clamps are connected correctly and firmly, and then turn Power
Switch to the ON position. The Connection Status Indicator LED will turn
Green, and the unit is now supplying current to your device.
C. After using, turn the unit off, and then disconnect the clamps.
D. Recharge the unit after use.
USING 12V CIGARETTE LIGHTER POWER
The 12V DC cigarette lighter outlet is protected by a 15 amp circuit breaker, which
resets automatically.
A. Turn Power Switch to the ON position;
B. Insert the 12V DC Cigarette Lighter plug from the device into the Cigarette
Lighter Outlet on the front panel, and the unit is now supplying current to your
device;
C. To use the unit with an external power inverter:
• Turn the external power inverter (not included) off;
• Plug the 12 V DC Cigarette Lighter plug from the power inverter into the
Cigarette Lighter Outlet.
• Turn the power inverter on.
• Plug the device into the power inverter. Use the below table to determine
approximate
14.5X21CM
4
Operating time
AC-powered Products
Cordless telephone
Fluorescent work light
Laptop computer , Table lamp
13" color TV
Spotlight, DVD Player, Sump Pump
* Operating time assumes a fully charged 8 AH battery and may vary based
on model used.
D. Reverse these steps after using.
E. Recharge the unit after use it, and Recharge it every 30 days.
NOTE: For best performance, make sure the unit is fully charged before using.
VOLTAGE TESTING
Fluctuations in temperature can accelerate battery discharge. Check the unit
often.
A. Press and release TEST / USB button and check the internal battery's voltage
level from three Battery Status Indicator LEDs.
• Green Indicator LED flashes and audible alarm sounds
Means the internal battery voltage is too high. Please check if the unit is on
charge wrongly.
• Green Indicator LED is on
Means the unit is charged and ready to be used.
• Yellow Indicator LED is on
Means the unit needs to be charged as soon as possible.
• Red Indicator LED is on
Means the unit is never used and needs to be charged immediately.
• Red Indicator LED flashes and audible alarm sounds
Means the internal battery voltage is too low. The unit is never used and
needs to be charged immediately.
B. Press and release the button again after test to prevent draining the battery
needlessly.
CHARGING JUMP STARTER USING AC/DC ADAPTOR
A. Plug the AC adaptor pin into the Jump starter
B. Plug the AC/DC adaptor into a 120V wall outlet
C. Continue charging until the Green Battery Status Indicator LED is kept on, and
then reverse these steps when charging is finished.
NOTE: The charger will automatically shut off to prevent overcharging. Leave
the unit plugged in to make sure it is charged for emergencies.
NOTE: Do not use while unit is recharging. Disconnect from charger before
use.
5
Watts Operating Time (Hours)*
5 20
14 7
40 2
60 1
100 0.5