DuraMax AD20538G Manual Del Operador página 4

USING AIR COMPRESSOR
The air compressor is rated for 100 PSI.
A. Remove the air compressor hose from the storage position. Install adapters as
necessary.
B. Attach the air compressor hose to the product or accessory to be inflated.
C. Turn COMPRESSOR Switch on and inflate the product.
D. When the product is inflated to the proper air pressure (using the air
compressor gauge), turn the switch to the middle position and remove the
hose.
E. Recharge the unit as soon as possible after use the air compressor.
NOTE: Do not run for more than 10 minutes maximum at a time. Allow it to cool
down for 10 minutes before using again.
INFLATING OTHER INFLATABLES WITH ADAPTERS (NOZZLES)
Inflation of other items requires use of one of the adapters (nozzles).
1. Select the appropriate adapter nozzle.
2. Lift the thumb latch on the nozzle, insert the adapter (i.e. needle) into the
nozzle connector and close thumb latch.
3. Insert adapter(i.e needle) into item to be inflated.
4. Turn on the Inflator Power Switch — inflate to desired pressure or fullness.
NOTE: Small items such as volleyballs, footballs, etc. inflate very rapidly. Do
not over-inflate.
5. Remove adapter.
6. Switch the Inflator Power Switch off.
7. Allow unit to cool before storing away.
8. Store inflator hose and tire fitting in storage compartment.
USING 5V USB POWER
The USB power outlet provides a maximum of 5V DC / 1.1A power to an external
USB-powered device.
A. Plug the USB-powered device into the USB power outlet.
B. Press and release TEST / USB button, and the Battery Status Indicator LEDs
will be on to show the battery voltage level.
C. Turn the device on.
D. Reverse these steps after using the USB power.
E. Recharge the unit as soon as possible after using the USB power.
NOTE: When the internal battery voltage is too low, the USB power will be shut
off automatically.
ADDITIONAL FEATURE
LOW VOLTAGE ALARM when using jump starter
When using the unit, for example, turning the Power Switch on, jump starting a
vehicle, using as 12V Power Outlet, using work light, etc, the microprocessor
inside the unit will detect the internal battery voltage automatically. Once the
internal battery voltage is too low, the Red Battery Status Indicator LED will flash
and audible alarm will sound for reminding you to charge the unit immediately.
When you stop using the unit or the internal battery voltage is back to normal, the
Red Battery Status Indicator LED will be OFF and the audible alarm will stop.
14.5X21CM
6
MAINTENANCE INSTRUCTIONS
TO PREVENT SERIOUS INJURY: Turn all switches to the OFF position before
performing any inspection, maintenance, or cleaning procedures.
TO PREVENT SERIOUS INJURY FROM TOOL FAILURE: Do not use damaged
equipment. If abnormal noise or vibration occurs, have the problem corrected
before further use.
1. BEFORE EACH USE, inspect the general condition of the unit. Check for loose
hardware, misalignment or binding of moving parts, cracked or broken parts,
damaged electrical wiring, and any other condition that may affect its safe
operation.
2. AFTER USE, wipe external surfaces of the tool with clean cloth.
3. Protect from sunlight and moisture.
4. LEAD-ACID BATTERIES MUST BE RECYCLED OR DISPOSED OF
PROPERLY. Do not short terminals. Do not incinerate.
CONTAINS SEALED NON-SPILLABLE LEAD ACID
Pb
BATTERIES. BATTERIES MUST BE RECYCLED.
Pb
1 YEAR WARRANTY
Every DuraMax Jump Starter is completely inspected before leaving the factory.
This product is warranted to be free of defects in material and workmanship.
Proof or purchase must be original store receipt.
DuraMax is a Trademark of Test Rite Products Corporation,1900 S. Burgundy
Place, Ontario, CA 91761 U.S.A.Made in China.
For questions regarding this product or warranty, please contact American
Customer Service at 1-855-232-6419, Monday through Friday, 8am to 8pm
Eastern Time Outside of Business hours you can reach us by e-mail 24/7 at
acs@americancustomerservice.com and we will reply to you on the next
business day. Please enter the QVC # in the subject line.
7