Publicidad
Idiomas disponibles
Idiomas disponibles
Tag Handling and Installation
Step 1 - Make sure that the intended mounting surface is clean and free of any contaminants.
NOTE: Handle the tags with care during installation. Do not excessively bend or distort the tag when
removing it from the liner.
Step 2 - Transfer the tag to the location on the vehicle that you have determined suitable for your
application. It is best to apply the tag by the edges as shown in the picture below.
Step 3 - Smooth out the tag to ensure complete adhesion and remove any air pockets.
NOTE: Once the tag has been mounted, do not attempt to remove the tag, this will damage the tag and it
will become inoperable.
Alternative Mounting
If mounting to the vehicle's headlamp is not feasible, you may also choose
to mount the tag on other plastic surfaces, such as the vehicle's bumper,
valance or side mirror. Many of the preceding guidelines will still apply
and the tag must still be mounted a minimum 2" (5 cm) from any metal
structures. This includes any metal structures behind the bumper, such as
metal grilles, bumper mounts or the vehicle's frame.
Cure Time
Once the tag has been installed on the vehicle, there will be a period of
time necessary to allow the tag's adhesive to cure. Due to temperature and
humidity variations the total cure time may vary. Most applications will
experience an 80% cure of the adhesive within 1 hour and full adhesive cure
within 24 hours of application. Please do not wash the area where the tag
is installed or disturb the tag for 24 hours after installation.
Programming Your LiftMaster tags into
LiftMaster Cloud
When adding a new credential in LiftMaster Cloud, go to the credentials
tab, click "Add new credentials" and when selecting type, choose
RFID_Tags_LiftMaster.
Please note, there is a section option for installations that have a Non
LiftMaster Branded RFID system. If the RFID system is anything other
than LiftMaster reader (LMSC1000) or LiftMaster RFID tags (LMUNTG/
SPLMUNTG or LMHNTG/SPLMHNTG), follow the steps above, except when
the drop down menu step comes up, choose RFID_Tags_Other_Mfgs.
01-39460
LMUNTG LiftMaster Dual-Purpose RFID Tag -
Removal
1. Gently peel the top layer of the RFID tag from the vehicle surface, the
adhesive and antenna tag layer should remain on the vehicle and is a
function of the tag's security.
2. Generously spray a mild glass cleaner on the adhesive layer and let it soak
in for around 10-20 seconds.
3. Using a micro-fi ber towel or cloth, rub the adhesive with the towel in a
circular motion. The adhesive should pull up in a similar manner to rubber
cement.
4. Repeat steps 2 and 3 until all of the adhesive is removed.
One Year Limited Warranty
All RFID Tags sales are fi nal. However, LiftMaster warrants to the fi rst
consumer purchaser of this product that it is free from defect in materials
and/or workmanship for a period of 1 year from the date of purchase.
NOTICE: This device complies with Part 15 of the FCC rules and Industry Canada's license-exempt RSSs.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesired
operation. Any changes or modifi cations not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC rules and Industry Canada ICES standard. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
© 2018, LiftMaster
All Rights Reserved
Tous droits réservés
Todos los derechos reservados
LiftMaster.com
Publicidad
