Dickson SP425 Manual De Instrucciones

Dickson SP425 & TP425
Getting Started
• Install DicksonWare™ (compatible with Windows®
98 or higher). DicksonWare™ version 14.8 or higher
required.
• If you already have DicksonWare on your PC check
the version by choosing "Help" and "About" from the
menu bar to check what version you have and make
sure it complies with the requirements of the logger.
• Open DicksonWare™ using the icon on your desktop.
• Connect the cable (supplied with the software) to the
logger and to a working USB port on your computer.
• Click the Setup button. You will be prompted to
select USB or Serial COM port, select USB and click
Continue. A Setup window will appear, and
all fields should be automatically filled in. This
confirms that DicksonWare™ has recognized the
logger. The logger is now sampling.
Display
Below are the possible display states and the conditions
they represent:
Solid or Scrolling (Logging)
• Logging normally. Pressing Start/Stop button will
stop logging. Pressing Start/Stop button again will
restart logging.
• No Delay selected in Setup–Logging normally
Flashing (Not Logging)
• selected in Setup but logging has
Start after Delay
not yet begun due to delay.
Need to Know
• When changing logger settings (sample interval and
start date and time) the logger will automatically clear
all stored data.
• To achieve longer battery life during operation, use a
less frequent sample rate and disconnect the unit from
the USB or serial port when not downloading data.
Fahrenheit/Celsius
The data logger is defaulted to log data in Fahrenheit. If
you want to view future logged data on the graph or table
in Celsius go to "File," "Preferences" and then change the
temperature selection.
Battery Replacement
The battery level monitor on the "Setup" screen displays
the battery voltage and a low battery warning when
replacement is needed.
The Dickson Warranty
Dickson warrants this line of instrument will be free from
defects in material and workmanship under normal use
and service for a period of twelve months after delivery.
All manuals and user guides at all-guides.com
Start/Stop Data Logger with Display Operation
• The logger is full and Stop When Full has been
selected in Setup. To clear logger, download to
DicksonWare and select Clear.
Blank (Not Logging)
• Press Button to Start has been selected in Setup but
the Start/Stop button has not been pressed.
• Start/Stop button has been pressed displaying "OF"
(short for OFF) to stop logging.
"OF"
• Displays for two seconds after Start/Stop button is
pressed to stop logging.
"ON"
• Displays for two seconds after Start/Stop button is
pressed to start logging.
Min/Max
There are two display options: Current Readings only or
Current/Min/Max scroll, which can be selected under
Setup/Display.
To reset Min/Max readings on the display, a paper clip or
toothpick should be used to depress the Min/Max Clear
button located on the back of the unit. This will not clear
logged data.
Press Button to Start
This feature needs to be selected when the logger is
setup (Setup/Samples). Hold down the Start/Stop button
on the front of the unit until "ON" appears on the display.
The logger is now logging. Pressing the button again will
stop logging.
When changing the battery the logger will not collect
data however memory will not be lost. To start sampling
again, download the data and then clear the memory.
Setting Plot Style
Spline and Points & Spline should not be used as they will
auto fill the graph over the period(s) where the logger is
off and not logging.
Start Mode
This logger has three start modes:
1. No Delay
2 Press Button to Start
3 Start After Delay
Each time the logger is cleared it will default to No Delay
and start logging immediately. To change start mode clock
on the Start Date/Time Setup button and select Delay
Type. Click ok.
This warranty does not cover routine calibration and
battery replacement
For Specifications and Technical Support go to
.
www.DicksonData.com