Troubleshooting - Suntec Wellness Klimatronic RAPIDO 9.0 Eco R290 Manual De Instrucciones

Ocultar thumbs Ver también para Klimatronic RAPIDO 9.0 Eco R290:
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 19
Operation mode cooling:
Press „MODE" until the indicating light „COOL" lights up.
o
Press the buttons „TEMP+" and „TEMP-" to adjust the desired room temperature between 16°C
o
and 31°C.
Press „SPEED" to adjust the ventilation speed.
o
Operation mode dehumidifying:
Press „MODE" until the indicating light „DEHUM" lights up.
o
The selected temperature will be set to current room temperature minus 2℃. The ventilation
o
speed is set as „LOW" automatically.
Operation mode ventilation:
Press „MODE" until the indicating light „FAN" lights up.
o
Press „SPEED" to adjust the ventilation speed.
o
Timer for turning on the unit:
Press „TIMER" while the unit is off and set the desired time at which the unit shall turn on by
o
using the buttons „TEMP+" and „TEMP-" between 0 and 24 hours.
Press „TIMER" again to confirm. The display shows the set time.
o
Timer for turning off the unit:
Press „TIMER" while the unit is on and set the desired time at which the unit shall turn off by
o
using the buttons „TEMP+" and „TEMP-" between 0 and 24 hours.
Press „TIMER" again to confirm. The display shows the set time.
o
Continuous drainage:
If you plan to leave this unit unused for a long time, please remove the rubber blockage from
o
the drainage hole (see exhaut hose installation, pic.2). Connect a drain hose to the hole to
empty the water tank completely.
If the water pump is defect, you can use the continuous drainage instead. In this case the water
o
pump is not activated, the unit can still work. Alternatively, in case that the water pump is defect,
remove the rubber blockage and connect the drain hose when the indicating light „W.F." („Water
Full") lights up. Please let the water drain through the drain hose and then remove the hose.
Close the rubber blockage of the drainage hole.
Cleaning
Always disconnect the appliance from the power outlet and let it cool before cleaning. Never immerse
the appliance in water to prevent electric shocks.
Wipe over the exterior of the appliance with a soft wet cloth and neutral detergent and then wipe dry
with a dry cloth.
Do not use gasoline or other chemicals to clean the unit.
Clean the dust filter once every two weeks. To do so, pull out the dust filter at the unit's side with the
help of the dust filter handle (see "parts description"). Clean the dust filter with neutral detergent and
lukewarm water, then let it air-dry before inserting it back into the unit.

Troubleshooting

Problem
1. Unit does not start
when pressing
"POWER".
2. It's not cool
enough.
3. Unit is too loud.
Possible causes
Water tank is full and indicating light
"W.F." is blinking.
Room temperature is lower than the set
temperature during operation mode
cooling.
Doors or windows are not closed.
There are heat sources in the room.
Exhaust hose is not installed or blocked.
Set temperature is too high.
Air inlet is blocked.
The ground is not even and flat enough
Suggestions
Empty the water tank.
Reset the temperature.
Close all doors and windows.
Remove the heat sources if possible.
Install the exhaust hose and make sure
that the hose is clean and not blocked by
any objects.
Reset the temperature.
Clean the air inlet
Place the unit on an even and flat surface.

Publicidad

Tabla de contenido

Solución de problemas

loading

Productos relacionados para Suntec Wellness Klimatronic RAPIDO 9.0 Eco R290

Tabla de contenido