Technical Assistance; Assembly Instructions; Battery Assembly; Drill's And Bits Accessory Assembly/ Replacement - VITO PRO-POWER VIBCBSFL20 Manual De Instrucciones

EN

2.6 - TECHNICAL ASSISTANCE

This machine must be repaired only by
the brand official technical service or
by qualified technicians and only with
original replacement parts.
3. ASSEMBLY
INSTRUCTIONS

3.1 - BATTERY ASSEMBLY

(FIG. B)
1. Insert the battery (11) in the drill's
fitting (7) and press it until listen
to a "click" of the battery's locking/
unlocking button. After this, the battery
is correctly placed;
2. To remove it, press the locking/
unlocking button and pull the battery;
Use VITO lithium batteries 20V.
3.2 - DRILL'S AND BITS
ACCESSORY ASSEMBLY/
REPLACEMENT (FIG. C)
Never assemble or
drills and bits accessories with the
equipment turned on. Always turn it
off before proceeding to any of these
operations.
1. Place the rotation mode selector (10)
into middle position to lock the "ON/
OFF" switch (9);
2. Hold the tool by the handle (6) with
one hand and untighten the quick chuck
(2) clockwise until the opening allows
inserting the drill or accessory;
3. Insert the drill or the bits accessory
into the quick chuck;
4. Hold the equipment by the handle
and tighten the quick chuck counter
clockwise until the drill or bits
accessory is completely fixed;
When using screwing bits, use the
universal bits accessory.
22
Make sure that the drill or bits
accessory
assembled and well tightened before
tuning the tool on. Misassembled or
loosen
accidents and injuries.
INSTRUCTIONS
This tool can be used to perform drilling
and tightening/untightening operations.
For that, drills and screwing bits are
used.
When operating the equipment, some
precautions must be considered:
� Do not apply too much pressure
against the working piece/object. If the
speed decreases abruptly, reduce the
pressure;
� When the tightening/untightening
accessory
equipment off immediately. Avoid
the reaction binaries that origin the
kickback;
replace the
� Never leave the machine before the
rotating part is completely stopped;
� Turn the machine off in case of:
- Lubricant leaking through the vent grid;
- Damages in the machine housing;
- Damages in the "ON/OFF" switch;
- Formation of smoke or smell of burnt;

4.1 - DRILL'S START AND STOP

(FIG. D)
1. Press the "ON/OFF" switch (9) and
lean the drill or accessory against the
surface or screw to drill or tightening/
untightening, respectively;
2. To increase and decrease the
rotation speed, press or relieve the
"ON/OFF" switch, respectively. The
maximum speed is reached when the
switch is fully pressed;
are properly
accessories may cause
4. OPERATING
gets stuck, turn
3. To turn the equipment off, release
the "ON/OFF" switch;
When the equipment is running, the
indicator led (8) is activated.
4.2 - SELECTING THE
ROTATION MODE AND
LOCKING THE "ON/OFF"
SWITCH (FIG. E)
Do not change the rotation direction
while the equipment is running: it will
cause serious damages to the tool.
Always check the rotation direction
before start operating the tool.
1. Use the rotation mode selector (10)
to select the shaft rotation direction:
� With the selecting button to the left
(a), the shaft spins clockwise (a);
� With the selecting button to the right
(b), the shaft spins counter clockwise
the (b);
� With the selecting button in the
middle, the "ON/OFF" switch (9) is
locked;
4.3 - SELECTING THE
ROTATION SPEED (FIG. F)
The equipment allows selecting two
speeds (1 and 2). Move the speed
selector (5) according to the desired
rotation speed and type of work;
1. Use speed 1 when using tightening/
untightening bits;
2. Use speed 2 when using drills for
drilling works;
The rotation speed can also be
adjusted through the "ON/OFF" switch
(9). The speed increases as the switch
is pressed.
4.4 -SELECTING THE
OPERATING MODE (FIG. G)
This equipment can be operated in
three different modes: drilling, impact
drilling and screwing.