HIKVISION DS-PD2-T12P-W Manual De Instrucciones

DS-PD2-P25-W
DS-PD2-T12P-WEL
25m Wireless Long Range Corridor PIR Detector 12m Wireless Outdoor Detector
E N G L I S H
Diagram References
1 Wireless device control
2 Registration
Please register the detector within 90 seconds after it being powered on.
Register Locally
1. Make the security control panel enter the registration mode.
2. Register the detector: Hold the registration key until the three LEDs flash
alternately.The green LED will flash 8 times if the registration is finished.
3. Communication Test: Release the TAMPER spring to trigger the alarm.
Note: The distance between the security control panel and the detector
should be less than 50 cm.
Initialize the Detector
1.Remove the battery to power the detector off.
2. 5s later,hold the registration key and reinstall the battery to power the
detector on at the same time to make the three LEDs start flashing alternately.
Release the registration key while the three LEDs flash once together.
Register Via APP
1. Log in to the APP Store and input" Hik-Connect" to search the mobile client.
Download and install Hik-Connect to your phone.
2. After installing,tap to run the client.
3. Power on the security control panel.
4. Log in the Hik-Connect and tap the icon"+" at the upper-right coner of the
Hik-Connect page to add the security control panel.You can scan the QR code
on the device rear panel or on the package box,or input the device serial No.
manually to add the device when the device is in the registration mode.
5. After adding the security control panel,tap the arming status icon on the
right of the security control panel's name to enter the Partition page.
6. Tap the"+" icon on Partition page to add the peripherals.
3 Diagnostics(Check Signal Strength Before Mounting)
4 Wired Tamper and Brackets
Technical Specification
Lens Characteristics
Detection Range 25m
Detection Angle 8°
Detection Zones 46 zones and 6 planes
Detection Speed 0.3–3m/s
Mounting Height 1.8-2.4m
Creep-zone Protection Yes
Key Features Y
Blue Wave Technology Yes
Digital Temperature Compensation Yes
Tamper Protection Front, rear, and bracket tamper signal input
Signal Strength Indicators (SSI)
Yes
Electrical & battery
Transmission Frequency 433MHz, FM transceiver
Range in Open Space 800m
3V Lithium Battery Included
1x CR123A
Minimum Battery Life (years)
2
Environment Features
Detection Range
Operation Temperature
-10°C to +40°C (Certified)
Weight
125g
Dimensions(H x W x D)
117 x 69 x 50mm
Accessories
Ceiling mounted bracket includedy
Yes
Wall mounted bracket included Yes
Battery Information
The batteries supplied have been chosen to provide long service life whilst,
for safety reasons, having limited output current.The battery is protected
on purchase by a piece of plastic that must be removed for operation.
When disposing of the product, the battery must be removed and disposed
of separately in accordance with the local regulations.
Electrical & battery
This product and - if applicable - the supplied accessories too are marked
with "CE" and comply therefore with theapplicable harmonized European
standards listed underthe RE Directive 2014/53/EU, the RoHS Directive
2011/65/EU.
For electrical products sold within the European
Community. At the end of the electrical products
life, it should not be disposed of with household
waste. Pleaserecycle where facilities exist.
Check with your local Authority or retailer for
recycling advice in your country.
1
HIGH
+ +
+ +
LOW
+ +
+ +
2
3
5s
+
-
4
LED ON LED OFF TAMPER
HIGH
LOW
REGISTRATION
+
-
A C
WALLBRACKET
B
D
CR123A
-
LITHIUM
+
-
+
>5s
-
REAR TAMPER
BREAK-OUT
E
A
=
BRACKET TAMPER
SEE SECTION4
=
REGISTRATION
8
CEILINGBRACKET
B C