Westin 32-2270 Instrucciones

AUTOMOTIVE PRODUCTS, INC.
BULL BAR ASSEMBLY
ENSAMBLE DE PARRILLA
DELANTERA CON TIRÓN
LA BULL BAR
32-2270
32-2275
ITEM QTY
1 1 BULL BAR ASSEMBLY
2,3 2 BRACKET, PASSENGER (2) AND DRIVER (3)
4 2 PLASTIC PLUG
5 4 RUBBER BUMPER
6 6 BOLT PLATE
7 6 1/2" FLAT WASHER
8 6 1/2" LOCK WASHER
9 6 1/2-13 HEX NUT
10 4 3/8-16 X 1.25" HEX HEAD BOLT, STAINLESS STEEL
11 8 3/8" FLAT WASHER
12 4 3/8" LOCK WASHER
13 4 3/8-16 HEX NUT
1 1 ENSAMBLE DE PARRILLA DELANTERA CON TIRÓN
2,3 2 PIEZA DE SUJECIÓN, LADO DEL ACOMPAÑANTE
4 2 TAPONES DE PLÁSTICO
5 4 PARACHOQUES DE HULE
6 6 PLACAS DE PERNOS
7 6 ARANDELA PLANA SAE DE 1/2"
8 6 ARANDELAS DE PRESIÓN DE
9 6 TUERCAS HEXAGONALES DE 1/2-13
10 4 PERNOS CON CABEZA HEXAGONAL DE 3/8 -16 x 1,25, ACERO INOXIDABLE
11 8 ARANDELAS PLANAS DE 3/8", ACERO INOXIDABLE
12 4 ARANDELAS DE PRESIÓN DE 3/8", ACERO INOXIDABLE
13 4 TUERCAS HEXAGONALES DE 3/8 - 16, ACERO INOXIDABLE
1 1 LA BULL BAR
2,3 2 SUPPORT CÔTÉ PASSAGER (2) ET CÔTÉ CONDUCTEUR (3)
4 2 BOUCHON DE PLASTIQUE
5 4 PARE-CHOCS EN CAOUTCHOUC
6 6 PLAQUES DE BOULON
7 6 RONDELLE PLATE SAE 1/2 PO
8 6 RONDELLE A FREIN 1/2 PO
9 6 ÉCROU HEXAGONAL 1/2-13
10 4 PERNOS CON CABEZA HEXAGONAL DE 3/8-16 X 1.25
11 8 RONDELLE PLATE SAE 3/8 PO
12 4 RONDELLE A FREIN 3/8 PO, ACIER INOXYDABLE
13 4 ÉCROU HEXAGONAL 3/8-16, ACIER INOXYDABLE
STEP 1. Remove the contents from box and check for damage. Verify all parts are present. Read instructions completely before
NOTE:
beginning.
NOTE:
It may be necessary to remove the front license plate and bracket. Remove license plate from bracket. Using a
STEP 2.
3/16" drill bit, drill out the two pop rivets that hold the bracket to the bumper. If local/state laws requires a license plate,
license plate relocation kit 32-0055 is available.
STEP 3. Remove tow hooks by removing the front bolt and rear bolt that threads into the side of the tow hooks. Tow hooks will not
be reinstalled.
Determine passenger and driver side brackets. Slide bracket in through the tow hook pocket. Align slots on bracket with
STEP 4.
holes on frame. Slide the three bolt plates inside the frame and out through aligned holes on both sides of the frame.
Secure with 1/2" yellow zinc fasteners. Leave loose.
NOTE:
Minor trimming of tow hook area may be needed. It may be necessary to clean out mounting holes on frame.
SEE FIGURE 2.
STEP 5. Attach Bull Bar to mount brackets using 3/8" stainless steel fasteners. Level and adjust Bull Bar as desired and tighten all
fasteners. Recommended torque values are 64 Ft. Lbs. for 1/2" yellow zinc fasteners and 17 Ft. Lbs. for 3/8" stainless steel
SEE FIGURE 2.
fasteners.
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION: 2007-08 CHEVY SILVERADO/ GMC SIERRA 1500 SERIES
APLICACIÓN: CHEVY SILVERADO MC SIERRA 1500, 2007-08
APPLICATION: CHEVY SILVERADO/GMC SIERRA 1500, 2007-08
1
CONTENTS - CONTENIDO
, STAINLESS STEEL
, STAINLESS STEEL
, STAINLESS STEEL
1/2"
, ACIER INOXYDABLE
Westin advises the installer to use a thread lubricant on all of the stainless steel fasteners.
- CONTENU
(2) Y EL CONDUCTOR
", ACIER INOXYDABLE
SEE FIGURE 2.
WO:
/G
2
3
TOOLS - HERRAMIENTA
3/4'' SOCKET
3/4" WRENCH
9/16" SOCKET
9/16" WRENCH
18MM SOCKET
18MM WRENCH
RATCHET
SOCKET EXTENSION
TORQUE WRENCH
UTILITY KNIFE
DADO DE 3/4 "
(3) LLAVE DE TUERCAS DE 3/4"
DADO DE 9/16 "
LLAVE DE TUERCAS DE 9/16"
DADO DE 18MM
LLAVE DE TUERCAS DE 18MM
MANERAL
EXTENSIÓN PARA DADO
LLAVE DE TORQUE
NAVAJA
CLE 3/4 PO
DOUILLE 3/4 PO
DOUILLE 9/16 PO
CLE 9/16 PO
CLE 18MM PO
DOUILLE 18MM PO
CLIQUET
RALLONGE DE DOUILLE
CLE DE COUPLE
COUTEAU
75-0767 REVISION A 10/24/07
6
- OUTILS