Westin 32-2130 Manual De Instrucciones

AUTOMOTIVE PRODUCTS, INC.
BULL BAR ASSEMBLY
ENSAMBLE DE PARRILLA
DELANTERA CON TIRÓN
LA BULL BAR
32-2130
32-2135
ITEM QTY
1 1 BULL BAR ASSEMBLY
2,3 2 BRACKET, PASSENGER (2) AND DRIVER (3)
4 2 PLASTIC PLUG
5 4 RUBBER BUMPER
6 6 BOLT PLATE
7 6 1/2" FLAT WASHER
8 6 1/2" LOCK WASHER
9 6 1/2-13 HEX NUT
10 4 3/8-16 X 1.25" HEX HEAD BOLT, STAINLESS STEEL
11 8 3/8" FLAT WASHER, STAINLESS STEEL
12 4 3/8" LOCK WASHER, STAINLESS STEEL
13 4 3/8-16 HEX NUT, STAINLESS STEEL
1 1 ENSAMBLE DE PARRILLA DELANTERA CON TIRÓN
2,3 2 SOPORTE
4 2 TAPONES DE PLÁSTICO
5 4 PARACHOQUES DE HULE
6 6 PLACAS DE PERNOS
7 6 ARANDELA PLANA SAE DE 1/2"
8 6 ARANDELAS DE PRESIÓN DE
9 6 TUERCAS HEXAGONALES DE 1/2-13
10 4 PERNOS CON CABEZA HEXAGONAL DE 3/8 -16 x 1,25, ACERO INOXIDABLE
11 8 ARANDELAS PLANAS DE 3/8", ACERO INOXIDABLE
12 4 ARANDELAS DE PRESIÓN DE 3/8", ACERO INOXIDABLE
13 4 TUERCAS HEXAGONALES DE 3/8 - 16, ACERO INOXIDABLE
1 1 LA BULL BAR
2,3 2 SUPPORT CÔTÉ PASSAGER (2) ET CÔTÉ CONDUCTEUR (3)
4 2 BOUCHON DE PLASTIQUE
5 4 PARE-CHOCS EN CAOUTCHOUC
6 6 PLAQUES DE BOULON
7 6 RONDELLE PLATE SAE 1/2 PO
8 6 RONDELLE A FREIN 1/2 PO
9 6 ÉCROU HEXAGONAL 1/2-13
10 4 PERNOS CON CABEZA HEXAGONAL DE 3/8-16 X 1.25
11 8 RONDELLE PLATE SAE 3/8 PO
12 4 RONDELLE A FREIN 3/8 PO, ACIER INOXYDABLE
13 4 ÉCROU HEXAGONAL 3/8-16, ACIER INOXYDABLE
Remove the contents from box and check for damage. Verify all parts are present. Read instructions completely
STEP 1.
before beginning. NOTE: Westin advises the installer to use a thread lubricant on all of the stainless steel fasteners.
STEP 2. NOTE: It will be necessary to remove the front license plate and bracket. Remove license plate from bracket.
Using a 3/16" drill bit, drill out the two pop rivets that hold the bracket to the bumper. If local/state laws requires a
license plate, license plate relocation kit 32-0055 is available.
STEP 3. Remove tow hooks by removing the front bolt and rear bolt that threads into the side of the tow hooks. On
passenger side, it may be easier to access the rear tow hook bolt with a 18mm wrench and going through the tow
hook pocket. Tow hooks will not be reinstalled.
Remove the tow hook pocket cover by releasing four clips per cover. Once all of these clips are released, start
STEP 4.
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION: 2007-08 CADILLAC ESCALADE ESV/EXT 1500
APLICACIÓN: CADILLAC ESCALADE ESV/EXT 1500, 2007-08
APPLICATION: CADILLAC ESCALADE ESV/EXT 1500, 2007-08
1
CONTENTS - CONTENIDO - CONTENU
, LADO DEL ACOMPAÑANTE
1/2"
, ACIER INOXYDABLE
(2) Y EL CONDUCTOR (3)
", ACIER INOXYDABLE
2
3
TOOLS - HERRAMIENTA - OUTILS
3/4'' SOCKET
3/4" WRENCH
9/16" SOCKET
9/16" WRENCH
18MM SOCKET
18MM WRENCH
FLAT TIP SCREWDRIVER
RATCHET
SOCKET EXTENSION
TORQUE WRENCH
UTILITY KNIFE
DADO DE 3/4 "
LLAVE DE TUERCAS DE 3/4"
DADO DE 9/16 "
LLAVE DE TUERCAS DE 9/16"
DADO DE 18MM
LLAVE DE TUERCAS DE 18MM
DESTORNILLADOR DE PUNTA PLANA
MANERAL
EXTENSIÓN PARA DADO
LLAVE DE TORQUE
NAVAJA
DOUILLE 3/4 PO
DOUILLE 9/16 PO
CLE 9/16 PO
TOURNEVIS A POINTE PLATE
CLIQUET
RALLONGE DE DOUILLE
CLE DE COUPLE
WO:
75-0729 REVISION C 4/23/08
6