Gardena TCS 20/18V P4A Instrucciones De Empleo página 13

(4)
1. Widen the belt clip , clamp it around the tube and tighten it with the
screw (5) .
(6)
2. Hook the carabiner onto the belt clip
3. Adjust the shoulder strap to the desired length with the quick release
fastener.
3. OPERATION
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v Wait for the chain to stop, remove the battery and slide the
protective cover over the bar before you adjust or transport
the product.
To charge the battery [ Fig. O1 / O2 / O3 ]:
CAUTION!
v Note the mains voltage! The voltage of the power source must
match the voltage specified on the rating plate of the charger.
For the GARDENA Pole Pruner Art. 14770-55 there is no battery
and no charger in the scope of delivery.
Thanks to the intelligent charging process, the charge condition of the
battery is automatically detected and then charged up with the optimal
charge current depending on battery temperature and voltage.
In this way, the battery is treated with care and remains permanently fully
charged when it is stored in the charger.
(A)
1. Push the locking button
holder (D) .
2. Connect the battery charger
3. Slide the battery charger (C)
When the battery charge indicator
the battery is being charged.
When the battery charge indicator
permanently green the battery is completely charged
(Charging time, see 7. TECHNICAL DATA).
4. Examine the charge status regularly while you charge.
5. When the battery (B) is completely charged, you can disconnect the
(B)
battery from the charger
Meaning of the indication elements:
Indication on the charger [ Fig. O3 ]:
Flashing of the battery The charging procedure is indicated by flashing of the battery charge
(Lc) (Lc)
charge indicator indicator
Note: The charging procedure is only possible when the battery
temperature is within the allowable charging temperature range,
see 7. TECHNICAL DATA.
Continuous lighting Continuous lighting of the battery charge indicator
of the battery the battery is fully charged or that the temperature of the battery is
(Lc)
charge indicator not within the allowable charging temperature range and can therefore
not be charged.
When the battery is not inserted, continuous lighting of the battery
charge indicator
socket outlet and that the battery charger is ready for operation.
Battery charge status indication
After starting the product, the battery charge status indication
is displayed for 5 seconds.
Battery charge status
67 – 100 % charged
34 – 66 % charged
11 – 33 % charged
0 – 10 % charged
If the LED (L1) flashes green, the battery must be charged.
(Wp)
If the error LED is illuminated or flashing, see 6. TROUBLESHOOTING.
To fill in chain oil [ Fig. O5 ]:
DANGER!
Physical injury due to chain breakage when the chain on
the bar is not sufficiently lubricated.
v Check whether sufficient quantities of chain oil are delivered
prior to each use.
14770-20.960.01.indd 13
(4)
.
(B)
and remove the battery from the battery
(C)
into a mains socket.
onto the battery (B) .
(Lc) at the charger flashes green
(Lc) at the charger illuminates
(C)
.
.
(Lc)
indicates that
(Lc)
indicates that the mains plug is inserted in the
(P) on the product [ Fig. O4 / O14 ]:
Battery charge status indication
(L1) , (L2) and (L3) illuminate green
(L1) (L2)
and illuminate green
(L1) illuminates green
(L1)
flashes green
We recommend to use GARDENA Chain Saw Oil Art. 6006 or an
equivalent mineral chain oil from a specialist supplier.
(7)
1. Unscrew the lid of the oil tank.
2. Fill chain oil into the filler neck
completely filled with oil.
(7)
3. Close the lid of the oil tank again.
4. Check the oil lubrication system.
The device must be cleaned thoroughly if oil has been spilled.
To check the oil lubrication system [ Fig. O6 ]:
(20)
v Point the bar at a bright wood cutting surface at a distance of
approx. 20 cm.
After operating the machine for one minute, clear traces of oil must be
visible on the surface.
CAUTION!
Never let the bar (20) come into contact with sand or soil as this
will lead to increased wear of the chain.
Work positions:
The Pole Pruner can be operated in 2 working positions (above / below).
To ensure a tidy cutting edge, thick branches should be cut in 2 steps
(Illustrations similar).
Saw above (thick branches) [ Fig. O6 /O7 /O8 ]:
1. Saw the branch from below max. 1/3 of the diameter (the chain slides
to the front stop (a) ).
2. Saw off the branch from above (the chain pulls to the rear stop
Saw below [ Fig. O6 /O9 ]:
v Saw off the branch from above (the chain pulls to the rear stop
To tilt the motor unit [ Fig. O10 ]:
(1)
The motor unit can be tilted in 15° increments from 60° to – 60°.
1. Keep both orange buttons
desired direction.
2. Release both orange buttons
To extend the telescopic tube [ Fig. O11 ]:
The telescopic tube (2) can be continuously extended by up to 50 cm.
1. Loosen the orange nut
2. Extend the telescopic tube
3. Tighten the orange nut
To start the pole pruner [ Fig. O1 /O12 /O13 /O14 ]:
DANGER! Risk of injury!
Risk of injury if the product does not stop when you
release the start lever.
v Do not bypass the safety devices or switches. For example do
not attach the start lever to the handle.
Verify that the following conditions are met before commencing
work:
– The tank has been filled with sufficient chain oil and the lubrica-
(P)
tion system has been checked (see 3. OPERATION).
– The chain is tensioned (see 4. MAINTENANCE).
To start:
The product is provided with a two-switch safety device (start lever
with starting lockout) to prevent the product from being turned on
by accident.
1. Put the battery (B) into the battery holder
2. Open the snap fit (13) of the protective cover and remove from the bar.
3. Hold the pole pruner with one hand on the insulated gripping surface
on the telescopic tube (2)
4. Slide the starting lockout
The pole pruner starts and the battery charge status indication
displayed for 5 seconds.
5. Release the starting lockout
To stop:
1. Release the start lever (16)
The pole pruner stops.
(8) (9)
until the viewing window
(11) pushed and tilt the motor unit
(11) and let the motor unit (1) engage.
(12)
.
(2) to the desired length.
(12) again.
(D) until it audibly engages.
and with the other hand on the handle
(15)
forward and pull the start lever
(15) .
.
is
(b)
).
(b)
).
(1) in the
(14) .
(16)
.
(P) is
13
11.09.20 14:05