RIKO brano Manual Del Usuario página 11

OPERATION MANUAL
UNFOLDING THE PRAM
To unfold the pram, put it flat on the ground (Fig. 1), and
pull vividly the handle up until the folding mechanism is locked
(Fig. 2, 3).
NOTE! Before starting to use the pram, make sure that it has been
correctly unfolded.
ASSEMBLING AND DISASSEMBLING THE REAR WHEELS
To disassemble the rear wheels, press down the button in the central
part of the wheel (Fig. 4) and remove the wheels from the axle (Fig. 5).
To assemble them again, press the button down and slide the wheels
onto the axle till they get locked.
NOTE! Before starting to use the pram, make sure that all the
wheels have been assembled correctly.
ASSEMBLING AND DISASSEMBLING
SWIVELLING WHEELS
In order to assemble the front wheels, force their axles
in the ends of the front legs, until you hear a characteristic
"click" (Fig. 6). In order to disassemble the wheels press down
the button at the upper part of the swivelling mechanism
(Fig. 7) and slide the wheel axle in.
The swivelling front wheels may be locked for going straight. In order
to lock the wheels, move down the plastic lever in the front part of the
swivelling mechanism (Fig. 8).
HANDLE HEIGHT ADJUSTMENT
It is possible to adjust the pram handle height. To perform the
adjustment, press down the round buttons on both sides of the handle
at the upper part, and then adjust the right height (Fig. 9a, 9b).
PARKING BRAKE
The pram is equipped with a rear parking brake. To engage the
brake, press its lever down (Fig. 10). In order to disengage it, lift the
lever.
NOTE! Before starting to push the pram, make sure that the brake
has been disengaged.
NOTE! Always engage the safety brake, when you leave the pram
on an inclined surface.
NOTE! The brake is not designed for slowing down. It should be
engaged after the pram has been stopped completely.
NOTE! The pram is not designed for running.
ADJUSTING SUSPENSION STIFFNESS
It is possible to adjust the stiffness of the pram's rear suspension.
The stiffness is adjusted using the lever under the rear suspension (fig.
11). Repeat for both rear wheels. The suspension has two settings:
stiff and soft.
ATTACHING AND REMOVING THE CARRYCOT
In order to attach the carrycot press it into the pram frame so that
the adapters on both sides of the carrycot lock onto the catches on
the pram frame (fig. 12a, 12b). They will lock in place automatically.
ATTENTION! Make sure the carrycot is attached correctly prior to
use.
To remove the carrycot press the buttons on the adapters at the
sides of the carrycot (fig. 13) and pull the carrycot upwards.
ASSEMBLING AND DISASSEMBLING THE SEAT
The seat should be assembled and disassembled the same way
as for the bassinet (see ASSEMBLING AND DISASSEMBLING THE
BASSINET Fig. 14a, 14b, 15).
The seat may be assembled with its front and back facing the
movement direction (Fig. 14a, 14b).
NOTE! Before starting to use the pram make sure that the seat has
been assembled correctly.
ADJUSTING THE FOOTREST
The pram is equipped with an adjustable footrest. To move it to the
right position, press down the buttons on its both sides (Fig. 16).
ASSEMBLING,
THE FRONT BAR
The seat is equipped with a safety front bar. To assemble it, slide the
plastic insets into the holes in the armrests (Fig. 17). To dismantle it,
press down the buttons located on both sides on the plastic insets and
THE FRONT
pull it up (Fig. 18). Position of the front bar may be adjusted. To place
it in the required position, it is enough to move it to the required side.
NOTE! Always use the seat equipped with the safety front bar.
RESTRAINT SYSTEM
The seat is equipped
(Fig. 19). It should be used from the moment a baby starts to sit by
itself. Unfasten the belts, by releasing the forks from the central buckle,
seat the baby, adjust the length of the belts so that they fit closely to the
baby's body, without oppressing it, and then fasten the forks of all the
belts to the central buckle.
The seat has an additional crotch strap which should be attached to
the safety bar using snaps (fig. 20). This is an additional element and
not be a substitute for using the 5 point safety harness.
NOTE! Always use the restraint system, if the baby can sit by itself.
SEAT CANOPY AND HANDLE FOR CARRYING THE SEAT
The seat comes with a canopy. Its frame also doubles up as a handle
for carrying the seat.
ATTENTION! Before lifting the seat, position it upright (perpendicular
to the ground) using the handle.
The canopy is adjustable. To position the canopy press the round
plastic buttons near its base (fig. 21).
ADJUSTING THE BACKREST
The seat is equipped with a four-step adjustment of the backrest
angle. To lower the backrest, pull up the plastic lever in the rear part
of the backrest (Fig. 22), and then set the correct position. To lift the
backrest, it is enough to push it upwards until the correct position is
achieved. It will get locked automatically (Fig. 23).
RAIN COVER
The pram comes with a leg rain cover. To put it on start from the
end next to the child and attach it to the canopy using snaps (fig. 24).
BAG
The pram comes with a practical bag. It attaches to the pram handle
using plastic carabiners at designated points above the handle height
adjustment (fig. 25). The bag also comes with an additional shoulder
strap and a practical baby changer.
DISASSEMBLING AND ADJUSTING
with a 5-point restraint system
RAIN FOIL
The pram is provided with a rain foil equipped with an air hole at
the baby's face height. To assemble it, put one end under the footrest
or under the bassinet rear, and pull the other end onto the canopy
(Fig. 26a, 26b). The foil is suitable both for the deep and stroller version.
MOSQUITO NET
The pram also comes with a useful mosquito net. To put up, slide
one end under the back of the carrycot and pull the other one over
the canopy (fig. 27). The mosquito net is designed to be used with
the carrycot.
CARRYCOT BACKREST ADJUSTMENT
The carrycot back rest angle can be adjusted. To set the required
position turn the knob under the carrycot clockwise or anticlockwise
(fig. 28).
CARRYCOT CANOPY AND HANDLE
THE CARRYCOT
The carrycot comes with a canopy. Its frame also doubles up as a
handle for carrying the seat (this is a handle for carrying the carrycot
and not the entire pram).
ATTENTION! Before lifting the carrycot, position it upright
(perpendicular to the ground) whilst holding it by the handle.
The canopy is adjustable. To position the canopy press the round
plastic buttons near its base (fig. 29).
ATTACHING AND REMOVING THE CHILD CAR SEAT
WITH AN ADAPTER
To attach the group 0+ child car seat, start by mounting the adapters.
The adapters are attached and removed analogous to the carrycot
(see ATTACHING AND REMOVING THE CARRYCOT)(fig. 30a, 30b.
31).
Click child car seats catches into the adapters (fig. 32, 33).
ATTENTION! Make sure the adapter and child car seat are correctly
attached prior to use.
The child car seat has an adjustable carry handle. In order to set
the handle in a required position, press the red buttons on both sides
(fig. 34).
To remove the child car seat, pull the levers on both sides of the child
car seat (fig. 35).
FOLDING THE PRAM
To fold the pram frame, align the front wheels with the mud guards
facing forward (fig. 36).
The folding mechanism is in the upper part of the handle bar. Press
the red safety lock on the right of the handle bar and then pull up on the
plastic levers on both sides (fig. 37). Hold the raised levers and push
the handle down.
Fold the frame half way (fig. 38), lift the basket so that its stiffening
element is above the plastic leg support (fig. 39) and then press the
handle all the way down to fold the pram entirely (fig. 40). The handle
bar may be adjusted to its lowest position to reduce the folded pram
size even further (fig. 41).
ATTENTION! Prior to folding the pram make sure the basket
stiffening element (i.e. its bottom) is above the plastic leg support.
FOR CARRYING
11