IN & OUT HOUSE EF197A Manual De Instrucciones página 19

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 41
E N
The communication frequency between the unit and the remote control has
already been preset. If you cannot use the remote control with the unit, follow
the instructions "Set up communication between the remote control and the
unit" to re-establish the connection.
R E M OT E C O N T RO L'S S TA N D BY M O D E
The screen shows the remote control's standby mode.
S W ITC H O N/O F F
Press this
button to switch the flame effect and the heater on or off. Press
this
button to switch the flame effect on or off in daily or weekly timer mode.
F L A M E E F F E C T
Press
to display the screen for adjusting the flame effect. Press the
button to select the three-level flame effect. Press the '+' and '-' buttons to
select the five levels of flame effect brightness and the OFF setting.
M O O D LI G H T
Press
to display the screen for adjusting the mood lighting. Press the
and
button to toggle through the 13 colours of the mood light or a colour
cycle mode. Press the '+' and '-' button to select the five brightness levels of
the mood light.
BAS E T R AY L E D LI G H T
Press the
button to access the screen for adjusting the LED light in the base
tray. Press the
and
button to toggle through the 13 colours of the LED light
or a colour cycle mode. Press the '+' and '-' button to select the five brightness
levels for the lighting.
N O R M A L M O D E
The normal control mode is set at the factory. If this is not the case, press the M
button until the logo
is displayed in the upper corner of the screen. Press the
'+' and '-' buttons to adjust the setting temperature from 17 °C to 25 °C in two
intervals. Press the button
to switch the heater on and off. ON and OFF are
displayed at the bottom of the screen.
36
E N
N OT E: It is normal for the fan heater to stop running for some time. This
happens because the room temperature is at or above the temperature
set on the remote control. The heating indicator is switched off after
10 seconds when the flame is on. The heating indicator stays on when
you only use the heating function.
TI M E R
H I N W E I S: This setting only applies to normal mode. This allows the unit
to switch to standby mode after a cer tain period.
Press the
button to switch between the settings OFF and 0.5 hours to
9 hours. The timer logo and time are displayed on the screen. The heater must
and
be in the ON position. The heater can be operated automatically using the daily
timer and the weekly timer on the remote control. Set the day, time and your
desired temperature.
Press the
button to activate the remote control. Press and hold the M button
for three seconds to display the settings screen. Press the
select the day, time or your desired temperature. The selected function is high-
lighted. Press the '+' and '-' button to set the value.
Time: 24-hour system
Select your desired temperature from 15–25 °C .
Temperature unit: °C , °F
TI M E R FO R DA I LY H E ATI N G
The following times are preset heating times that can be altered if desired.
6:00 a.m. to 8:30 a.m., 5:00 p.m. to 10 p.m.
Press the M button until
and then enter the daily heating interval. Press
six seconds to display the daily timer settings. Maximum three heating periods
per day.
Press
or
The minute indicator will increase/decrease by 15 minutes per press.
Press
and hold the button for three seconds or wait 10 seconds to save
and exit the heating time setting.
D
is displayed in the upper right corner of the screen
and hold the arrow button for
to select hour or minute, press '+' or '-' to set the time.
and
button to
37

Publicidad

Tabla de contenido
loading

Tabla de contenido