Know Your Product; Operation - SPARKY VC 1220M Manual De Instrucciones

handling electric appliances. The above men-
tioned groups must never work with this elec-
trical appliance. It is also imperative that you
observe the accident prevention regulations in
force in your area. The same applies for general
rules of occupational health and safety.
▪ The manufacturer shall not be liable for any
changes made to the appliance nor for any
damage resulting from such changes.
IV - Know your product
1. Handle
2. ON/OFF switch
3. Automatic mode switch (VC 1430MS)
4. Upper section
5. Float switch
6. Filter basket
7. Built-in socket (VC 1430MS)
8. 2 castors
9. Clamps
10. Tank
11. Connection for the vacuum hose
12. 2 big wheels
13. Hose set
14. Telescopic tube
15. Combo brush for floors and carpets
(VC 1430MS)
16. Blower connector
17. Crevice nozzle
18. Pleated filter
19. Foam plastic filter
20. Dry filter
21. Drain outlet (VC 1430MS)
22. Adapter (VC 1430MS)
23. Air control handle (VC 1430MS)
24. Dust bag
25. Floor nozzle (VC 1220M)
26. Holder for extension tube
27. Screws
UNPACKING
Due to modern mass production techniques, it is
unlikely that your electric appliance is faulty or that
a part is missing. If you find anything wrong, do not
operate the appliance until the parts have been
replaced or the fault has been rectified. Failure to
do so could result in serious personal injury.
Carefully unpack the contents of the box.
1. Hold the two clamps (9), which hold the upper
section (4) in its position and fold them upwards
(Fig.1).
2. Loosen the clamps, remove the upper section
Original instructions
(Fig.2), and remove the contents from the tank.
Please check the parts using the list shown above
to make sure they are complete and that there has
been no damage in transport.
ASSEMBLY
▪ Make sure that the cable is unplugged.
▪ Hold the two clamps, which hold the upper
section in its position and fold them upwards
(Fig.1).
▪ Loosen the clamps and lift the upper section up
and out (Fig.2).
▪ Slide the handle onto the upper section from
the top. Make sure that the guide of the handle
fastener is inserted on the right side in the han-
dle holder (Fig.3).
▪ Fasten the handle to the upper section with the
two accompanying screws. Tighten the screws
finger-tight (Fig.4).
▪ Turn the tank over so that the upper section is
on the bottom.
▪ Put the four rollers (8, 12) in the guides on the
bottom of the tank (Fig.5).
▪ Check that the rollers have been pushed com-
pletely into the guides.
▪ Fasten the rollers with the remaining screws.
▪ Tighten the screws finger-tight (Fig.6).
▪ Insert a filter, appropriate for the intended op-
eration.
▪ Replace the upper section on the tank (Fig.7).
▪ Align the upper section with the clamps (Fig.8).
▪ Hook the clamps into the upper section and let
them snap into place by pressing the clamps
downwards.
▪ Place the large end of the hose (13) on the front
air intake stub (11) on the tank.
▪ Select a nozzle (15, 17, 25) or the telescopic
tube (14) and slide it over the suction tube (13)
(Fig.10).
▪ After using and cleaning the appliance, store
the accessories by attaching them to the cor-
responding holders on the vacuum cleaner
(Fig.11).
V - Operation instructions
These electric appliances are supplied from single-
phase alternating current mains only. Model VC
1220M is double insulated according to EN 60335-1
and can be connected to grounded or not grounded
sockets. Model VC 1430MS must be connected to
grounded sockets.
This power tool is radio suppressed in compliance
5
EN