Bellelli Nanna Guri Instrucciones De Uso página 15

A. Carry handle
B. Rear seatbelt guide
C. Rear compartment
D. Carry handle button
E. Cover
F. Booster cushion for newborn infants
G. Side seatbelt guide
H. Adjuster strap
I. Adjuster button
J. Buckle padding
K. Buckle
L. Safety harness
M. Harness padding
N. Pushchair release button*
O. Sunshade
*Check which version you have purchased. For
use consult the pushchair manual.
P P r r e e l l i i m m i i n n a a r r y y a a d d j j u u s s t t m m e e n n t t o o f f t t h h e e c c h h i i l l d d s s e e a a t t
Adjust the height of the safety harness (L)
before fitting the child seat in the vehicle.
A A d d j j u u s s t t i i n n g g t t h h e e h h e e i i g g h h t t o o f f t t h h e e s s a a f f e e t t y y h h a a r r n n e e s s s s
Put the child seat on the floor.
Place the child in the seat.
Check that the harness straps are adjusted to
the position closest to the child's shoulders, and
preferably in the position just below the child's
shoulders.
H H o o w w t t o o m m o o v v e e t t h h e e c c h h i i l l d d s s e e a a t t h h a a r r n n e e s s s s
Press the red buckle button (K) to open it (fig. 2).
Remove the padding (M) (fig. 3).
Open the compartment on the back of the seat
(C) (fig. 4).
Unthread one harness strap from the backrest
(fig. 5) and thread it back in at the required
height (fig. 6).
Repeat with the other strap.
Close the compartment (C).
Replace the padding (M) (fig. 7).
Unite the buckle clips.
Insert the united clips into the buckle (K). A click
indicates correct fastening of the buckle.
Finally, pull the adjuster strap (H).
Warning: ensure that the straps are not twisted.
C C a a r r r r y y h h a a n n d d l l e e
The carry handle (A) has four different positions:
- Vehicle use (fig. 8 a).
- Transport (fig. 8 b).
- Rest / rocking (fig. 8 c).
- Rocking stop (fig. 8 d).
H H o o w w t t o o a a d d j j u u s s t t t t h h e e c c a a r r r r y y h h a a n n d d l l e e
Simultaneously press the release buttons (D)
located on the sides of the carry handle (fig. 9).
Move the carry handle (A) in the required
direction, forward or back. The two buttons will
click out when one of the locking positions is
reached.
Warning: before use always check that the
transport handle is correctly locked in position.
H H o o w w t t o o p p o o s s i i t t i i o o n n t t h h e e c c h h i i l l d d
Warning: Use the infant booster cushion (F) for
children under the age of three/four months.
Press the adjuster button (I) and at the same
time pull both the child seat harness straps (L)
(fig. 10).
Press the red button on the buckle (K) to open it
(fig. 11).
Separate the buckle clips and rest them on the
sides of the seat (fig. 12).
Position the child in the seat (fig. 13).
Unite the buckle clips (fig. 14).
Insert the united clips into the buckle (K) (fig.
15). A click indicates the correct closure of the
buckle.
Position the padding (M) over the child's
shoulders (fig. 16).
Pull the front adjuster strap (H) to tighten the
harness straps on the child (fig. 17).
Warning: During the journey periodically check
that the child is still correctly strapped into the
seat.
H H o o w w t t o o r r e e l l e e a a s s e e t t h h e e s s t t r r a a p p s s
Press the adjuster (I) and simultaneously pull
both the harness straps (L) to slacken them (fig.
18).
Press the red button on the buckle (K) to open it
(fig. 19).
Separate the harness straps and move them
away from the child (fig. 20).
13