How To Disassemble; How To Clean - Richell 94903 Manual De Instrucciones

❹
Tighten the upper Adjuster Knobs on each side until clearance between the Gate Door and Main Frame is set to about 0.12" as shown in Figure 4.
❺
Tighten the lower Adjuster Knobs to give enough tension force. Then install the product against the wall vertically as shown in Figure 5.
Warnings!
The width of the Adjuster Bolts on each side must be set equally to avoid
●
unexpected accidents and/or product damage as shown in Figure 4.
Tighten the Adjuster Knobs until clearance between the Gate Door and
●
Main Frame is set to 0.12". This allows the tension-spring effect to work
properly to avoid unexpected accidents and/or product damage.
Figure 5
Side of the Main Frame should
be parallel to the wall.
7. Installation Check / How to Open and Close the Door
When correctly installed, the gate should not feel loose or
wobbly when tugged.
Using hands to open/close the Door
●
To open the Door, grab and lift the top of the Door up to
release the Upper/Lower Locks. To close the Door properly,
shut the Door until the Upper/Lower Locks click.
Using feet to open/close the Door
●
(1)
Step on the Foot Pedal until the bottom touches the floor.
(2)
Press body against the Door to keep it open while passing
through it.
To close the Door properly, press body against the Door while
shutting it; and make sure Upper/Lower Locks are securely in place .
The Door opens at a 90-degree angle.
●

8. How to Disassemble

Rotate Adjuster Knobs counterclockwise to loosen and remove.
Cautions! Be careful not to drop the product during disassembly.
●
Make sure the Door is locked during disassembly.
●

9. How to Clean

Use a mild detergent and water and clean with a soft cloth/sponge. Cleaning with a scrub brush and/or using a polishing
●
powder may cause scratches, rust and/or discolor this product.
When using creosol or other disinfectants, make sure to dilute them, otherwise damage to the product or discoloration may occur.
●
Do not use harsh chemicals such as thinner, benzene or alcohol. These may cause damage/discoloration to the wooden finish.
●
After cleaning, wipe dry with soft cloth or place in shaded area to air dry; do not place product in direct sunlight. This may
●
cause discoloration, deformation, or rust.
10. Specifications
UPC/JAN
803840 94903-0 / 4973655 98797-1
28.3 - 37.2"W x 8.7"D x 36.6"H
Dimension
Wood part: Natural Wood (Rubber Wood, Laquer finish) ; Frame, Wire: Steel (Polyester coating) ;
Material
Cover for Door Lock Pin, Shaft Component, Adjuster Cap: Polypropylene; Lock Pin: Polyformaldehyde ;
Adjuster Bolt Rubber part
Please note that product specifications and design may change without prior notice for the purpose of quality improvement.
●
There may be coating cracks at some joints and each product may experience different coloration of the wood grain as frames are made of natural wood.
●
If you find something wrong with this product, please let us know. Thank you!
●
Replacement parts may be purchased by contacting Richell USA directly at the number listed below or at www.richellusa.com.
One side of Adjuster Knob
is longer than other side.
Elastomer ; Pedal: Nylon
:
4
About 0.12"
Figure 4
Door
One side of Adjuster Knob
is shorter than other side.
Using hands to open/close the Door
●
Door
Upper stopper
Using feet to open/close the Door
●
Pedal
Adjuster Bolts on each side
must be set equally
Main Frame
Side of the Main Frame
should be parallel to the
wall surface.
Lower stopper
*The Foot Pedal is designed
to open the Door based on
adult weight. It is not designed
to be opened by pets.
For USA Customers
Designed by:
Richell Corporation, Japan
Distributed by:
Richell USA, Inc.
Grand Prairie, Texas 75050
Phone (972) 641-9795 Fax (972) 641-8495
www.richellusa.com
Visit us at
MADE IN VIETNAM