Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
other condition that may affect the power tool's
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f ) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g ) Use the power tool, accessories and tool bits etc.,
in accordance with these instructions taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5) Service
a ) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Additional Specific Safety Rules for Breakers
•
Ensure the chisel is secured in place before operating the tool.
•
In cold-weather conditions or when the tool has not been used
for a longer period of time, let the tool run with no load for
several minutes before use.
•
Always hold the tool firmly with both hands and ensure a
secure stance. Always operate the tool with the side handle
properly mounted.
•
When working above ground level ensure the area below is
clear.
•
To prevent electric shock, check the working area for live wires
before operation.
•
Do not touch the chisel or the parts close to the chisel
immediately after operation, as they may be extremely hot
and cause burns to the skin.
•
Always direct the power cable to the rear, away from the
chisel.
•
Keep the power cable away from the accessory. A power cable
wrapped around the bit may cause electric shock.
•
Do not wrap the power cable around your body.
•
Do not allow inexperienced users to use this tool.
•
Wear ear protectors. Exposure to noise can cause hearing loss.
•
Use auxiliary handles supplied with the tool. Loss of control
can cause personal injury.
•
Do not strike jammed accessories with a hammer to dislodge
them. Fragments of metal or material chips could dislodge
and cause injury.
•
Always switch off the tool when work is finished and before
unplugging.
•
Do not recondition accessories yourself. Chisel reconditioning
should be done by a qualified specialist. Improperly
reconditioned accessories could cause injury. Only slightly
worn accessories can be resharpened by grinding.
WARNING: We recommend the use of a residual current
device with a residual current rating of 30mA or less.
Residual Risks
The following risks are inherent to the use of breakers:
•
Injuries caused by touching the hot parts of the tool.
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided. These are:
•
Impairment of hearing.
•
Risk of squeezing fingers when changing the accessory.
•
Health hazards caused by breathing dust developed when
working in concrete and/or masonry.
•
Physical trauma due to inappropriate lifting and carrying of
heavy equipment.
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the power supply corresponds to the voltage
on the rating plate.
Your D
WALT tool is double insulated in accordance
e
with EN60745; therefore no earth wire is required.
WARNING: 115 V units have to be operated via a fail-safe
isolating transformer with an earth screen between the
primary and secondary winding.
If the supply cord is damaged, it must be replaced by a
specially prepared cord available through the D
service organisation.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
•
Safely dispose of the old plug.
•
Connect the brown lead to the live terminal in the plug.
•
Connect the blue lead to the neutral terminal.
WARNING: No connection is to be made to the
earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
Using an Extension Cable
An extension cord should not be used unless absolutely
necessary. Use an approved extension cable suitable for
the power input of your charger (see Technical Data). The
minimum conductor size is 1.5 mm
is 30 m.
When using a cable reel, always unwind the cable completely.
Package Contents
The package contains:
1 Breaker
1 Instruction manual
•
Check for damage to the tool, parts or accessories which may
have occurred during transport.
•
Take the time to thoroughly read and understand this manual
prior to operation.
EngLIsh
WALT
e
; the maximum length
2
17
Publicidad
Tabla de contenido
